Search:

Hi Kay,

I have the same machine. It is a dinosaur but still cuts :)

If you want to send me the file, I can cut it on my machine to see if the same thing is happening. If both machines make the...

Hey Steve,

I have the braille software and could help you out with a few signs if you just want the dxf. Still want to visit your shop one of these days, but life gets so so busy...

Mike Ross

Hi Guys,

I purchased, downloaded and installed the braille plug-in but am having trouble finding it :( I have emailed Aaron and Keith but have not heard anything back yet.

I am running Corel...

Hi,

I purchased, downloaded and installed the braille software per instructions.

Running Corel V12 on vista.

I go to tools, but do not see the macro in the drop down.

Any suggestions?

Thanks for the suggestions guys, before I asked for help, I tried to open/import in auto cad, rhino, corel draw, illustrator, photoshop. My apologies for not saying that up front.

Solved it by...

Good Morning,

Looking for a way to convert a .plt file to a .cdr. Any suggestions or advice? Appreciate your thoughts.

Mike Ross

Hi David, lots of folks on here with the equipment and knowledge, let us know where you are located, I bet someone local to you can help.

I sketched what I think you are trying to make. Hundreds of A and B.

Is this correct?

Mike Ross

Looks like spalting to me. So its a good thing! Merry Christmas!

Mike Ross

Thank you to Mike Mackenzie for the advice and selling me a power supply. I am back up and running. Mike had a used model in stock and provided it at a very reasonable price.

Thank you also to...

I use 3/4 inch pipe, lift one end of your project on it then just roll it on the pipe. Sometimes I use 2 or 3 pipes, moving them into the path I want to go, as I go. Works especially great for large...

Gentleman,

I greatly appreciate the options you have all generously provided. This forum is truly amazing.

Mr. Mackenzie, I emailed you images of the Power Supply.

Mr. Laubscher, I PM you a...

Hi Dan,

Thanks for the advice, I am a complete novice on power supplies and appreciate the input and knowledge.

I used a volt meter, have not disconnected any wires from the unit so it should...

Thanks Mike, I will email you a photo of the the suspect unit. It is silver and does say omega, although the book identifies it as 28V? I misread omega as mega.....

Greatly appreciate your...

I have a 1997 ULS 25E.....Pretty sure the 28Vpower supply is not functioning properly. I determined this because the service manual says:

(Paraphrased)
If the laser does fire and the fans do not...

Hey Mark,

If sanding works you are welcome to come out and use my edgesander. Be good to see you again,

Mike Ross

I have minimal heat in the shop. When it gets cold I put a light under the laser bed and leave it on. The incandescent bulb keeps it pretty toasty and dry in there. Its eliminated erratic behavior on...

Thank you gentleman, it was the apply to duplicate that solved my issue.

Cheers,

Mike

Hey Creekers,

Using Coreldraw 12 (I know).

When I select an object or group and drag to move, I get multiple copies of the selection. So if I grab a d and move it, it looks like ddddddd. If...

Thanks guys, I ended up routing it, and your right. The laser was not the right tool but it came off the router perfect! Looking forward to trying sublimation on masonite.

Mike Ross

Onsrud has a chip load calculator on their website.
https://www.onsrud.com/xdoc/FeedSpeeds
It separates material by Hardwood, Softwood, Plastic etc... Does not break it down to Red Oak vs Alder...

Hi Guys, This sounds like a great tool and I would throw a few dollars in the pot.

Mike Ross

Howdy, Have a customer that wants their logo cut out of Rowmark FRP that will then be dye subbed. Anybody try this or care to share some thoughts? My Plastic vendor says Rowmark does not recommend...

I would like to be included please.

Mike Ross

Exciting and scary at the same time!!

Scott, if I were in your situation I would call the client and explain the situation. Explain that the called for materials are more than you anticipated at...