Search:

Type: Posts; User: Alan Bienlein; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    17
    Views
    6,371

    I bought all of my duct work at home depot fro my...

    I bought all of my duct work at home depot fro my system and can close all of my blast gates without fear of collapse. I ran the duct work thru wooden rings to support it and prevent that from...
  2. Replies
    8
    Views
    1,459

    I wouldn't call something like that crappy. Those...

    I wouldn't call something like that crappy. Those exact same slides my father installed in the kitchen he built for his house over 45 years ago and they were still working perfectly when we sold the...
  3. Replies
    17
    Views
    2,272

    i live just NW of Houston and never had a problem...

    i live just NW of Houston and never had a problem with rust on the tools. I just wax them as needed. The summers are hot and can be humid but I think they are way more comfortable here than where I...
  4. 358665358666 This is how I store my veneer...

    358665358666

    This is how I store my veneer about my garage door. It's about 8' x 8'.
  5. http://www.sawmillcreek.org/image.php?u=9437&datel...

    http://www.sawmillcreek.org/image.php?u=9437&dateline=1229666576John Terefenko
    http://www.sawmillcreek.org/images/statusicon/user-offline.pngMember



    Join DateOct 2006LocationNew JerseyPosts939
  6. This is how you do it. No need for any thing else...

    This is how you do it. No need for any thing else such as soldering or crimping on connectors. I was taught this by an electrician I was working for.
  7. Replies
    6
    Views
    1,840

    Today he gave the gun a good cleaning and so far...

    Today he gave the gun a good cleaning and so far problem has went away. Looks like it might not have been atomizing the lacquer fine enough trapping air in it.
  8. Replies
    6
    Views
    1,840

    Its a gravity fed spray gun. Everything is wiped...

    Its a gravity fed spray gun. Everything is wiped and blown off with and oil less compressor from california air. The process is to seal with de-waxed shellac. From there it gets about 2 coats of...
  9. Replies
    6
    Views
    1,840

    Bubbles in lacquer on inside corners

    We have been having some problems lately with the finish bubbling on the inside corners of guitars that are being finished with lacquer. It happens either at a neck joint or at the bridge on a steel...
  10. Replies
    11
    Views
    2,362

    They also upgraded the brake by applying a...

    They also upgraded the brake by applying a plastic coating to the aluminum brake so that when you do hit a piece of metal the it won't trip if pieces are caught in the teeth of the blade and happen...
  11. Replies
    27
    Views
    4,422

    No recycling here. We burn our mail and yard...

    No recycling here. We burn our mail and yard waste along with any wood scraps from the shop. Everything else that can't be burnt is put in one trash can for pickup.
  12. Replies
    74
    Views
    20,767

    I went with the Sam's club version in my shop. I...

    I went with the Sam's club version in my shop. I replaced 4 T1296 HO 110 watt two tube fluorescent fixtures totaling 68,800 lumens to 10 of the lights of America 4' led shop lights totaling only...
  13. I made all of my own wye's using the free pipe...

    I made all of my own wye's using the free pipe joint template software at www.harderwoods.com .
  14. Nothing as I always buy my tools when I need them.

    Nothing as I always buy my tools when I need them.
  15. Strip the wire and twist the strands in the...

    Strip the wire and twist the strands in the opposite direction and then bend your hook. When you tighten the screw it will naturally pull the strands under the screw.
  16. I've had way to many problems with holes in the...

    I've had way to many problems with holes in the flex from the cyclone to the drum from abrasion so I ended up buying an inner tube for a truck tire. It makes it's own air tight seal and no clamps are...
  17. Honestly without pictures it sounds like the...

    Honestly without pictures it sounds like the pulley was loose for some time and just chewed the shaft up. If that were the case I would just replace the cutter head and the pulley.
  18. Replies
    24
    Views
    4,803

    In the previews of the season finally Gibbs asked...

    In the previews of the season finally Gibbs asked Tony if he was looking for Ziva. Now with Tony leaving it's just not worth watching anymore as there will be no more interesting characters.
  19. They sure are. Just come on down to Texas as you...

    They sure are. Just come on down to Texas as you can't swing a dead cat without hitting one!
  20. Replies
    19
    Views
    7,459

    Here is a link to the thread but I'll post my...

    Here is a link to the thread but I'll post my measurements here. http://www.sawmillcreek.org/showthread.php?213202-Preliminary-test-measurements-on-my-dust-collection-system&highlight=With all the...
  21. Thread: Woodnet

    by Alan Bienlein
    Replies
    4
    Views
    1,802

    I'm a member there and didn't have a problem but...

    I'm a member there and didn't have a problem but then again I use my real name on any forum that I'm a member of.
  22. Replies
    20
    Views
    14,658

    What happened to Accuhead? I bought one of their...

    What happened to Accuhead? I bought one of their heads for my TP1300 planer and about a year later they just disappeared. That was the best $250 I ever spent on an upgrade for one of my tools.
  23. Replies
    10
    Views
    2,462

    Double check and make sure that isn't the one...

    Double check and make sure that isn't the one that only cuts at 90 degrees to the table. They had a model where the blade didn't tilt and I only see one hand wheel.
  24. Replies
    6
    Views
    1,789

    Have you thought about DUI hei distributors for...

    Have you thought about DUI hei distributors for Ford?
  25. Replies
    5
    Views
    1,372

    Poll: Any of those that you have on hand will work just...

    Any of those that you have on hand will work just fine.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4