Ken - though I don't have that particular device, my experience with electronic equipment says that the first thing to do is change the battery. That usually takes care of 95% of my problems.
Doug
Type: Posts; User: doug faist; Keyword(s):
Ken - though I don't have that particular device, my experience with electronic equipment says that the first thing to do is change the battery. That usually takes care of 95% of my problems.
Doug
Dan - just wondering where you're going to get the paper. I have a 22-44 and these abrasives sound like a very good (albeit expensive) deal.
Doug
Richard - I've had my Laguna TSS on 6" oak blocks since I brought it home six years ago. It's a great height for me and still solid as a rock
Doug
Yeah, they are expensive, but I think I'll give it try for a roll or two.
Thanks for the info.
Doug
Where does one buy Abranet paper.
Doug
No takers, Huh?
Doug
I have a friend with a nice looking burl who would like to have the burl turned into a bowl.
Anyone here have that kind of expertise and would be interested in taking on the project? If so, in...
Bill - I guarantee you will find a tear in your eye every time you watch her rock in her new chair.
Very nicely done, Gramps!
Doug
Unbelievable, Sam! Fantastic job.
I'm curious, are these in a home, commercial building, or what?
Doug
"Something a little more stout". Really? You plan on parking your car on it? It's really starting to look awesome.
I built my bench about 6 years ago. Finished the top (3" maple") with just...
My rule of thumb, especially for larger pieces like this, is 3-4 x material cost. I've found it comes pretty close to spending a couple hours on wood, electricity, finishes, incidental costs, etc.,...
I'm wondering if this is a technique problem rather than a wood problem. If pressure is applied to the in-feed table throughout the pass, you may get a taper at the end. Try pressure on the...
Richard - there is one progressing on a different forum.
http://www.woodcentral.com/woodworking/forum/messages.pl/page/1/md/read/id/460033/sbj/chevalet-de-marqueterie/
Dave - speaking as a 26 year cancer survivor, I can say that the stuff they give you sucks, but it's effective.
Apparently the cancer fighting drugs also instill innate woodworking abilities. The...
Jack - you might want to keep an eye out for a used INCA. I'm thinking of one like I had sometime back, the 259. Small footprint, built like a tank but with clockwork precision, nice fence, too. ...
I've had a craftsman TS, a tilting table INCA, then an INCA 12" with an Excalibur sliding table added, then a Laguna TSS.
My opinion on sliders has changed completely over the years. I'm now...
Dick - Nice job on the restoration; it shows a lot of dedication and patience.
Based on stuff in my neck of the woods, seems like a fair asking price would be in the $500-$700 range. YMMV
Doug
You're killing me here; how much was the Uni??
Doug
I agree with Mike on this one. The drawers on the router station really don't get that much use over time (as compared to a dresser used 4-6 times every day).
So try the wax first; if it wears...
This video has a bit of a different perspective on how to adjust a bandsaw. I've tried it and it works.
http://www.youtube.com/watch?v=wGbZqWac0jU
Just one more opinion.
...
Mark - I have read this thread several times and have yet to figure out exactly what your point is here. My experience has been that "&%St" happens; products fail. When I contact the company if...
unless your workbecnch is grossly out of level, a wedge under the shortest leg has always worked for me. I am much more concerned that the bench is FLAT and not twisted; level doesn't make a whole...
Is this the one?
http://www.youtube.com/watch?v=wGbZqWac0jU
Just a guess, Shawn, but I would venture that Freud MADE the set slightly undersized to compensate for the 1/4" plywood that is so rarely a full 1/4". That's gap can easily made to fit perfectly...
Mark - thanks for the tour. I'm curious, did you have to make prior arrangements to see the school or was it just a walk-in? We're planning a road trip this summer and that would be a highlight.
...