Search:

Please count me in.

Thanks,
G.L.

Please include me in this drawing.

Thanks,

G.L.

It helps to be logged on with Admin privileges when installing programs. The window that came up did not look like the other times when I tried to install programs.

That is my story and sticking...

Hello Everyone,

Having a problem with Cut List. DL from the link provided at Lumberjocks.

When extracting the files to the Plugins directory for SU I get a prompt for a password.

Have I...

Thanks for your responses. Need to be clear when posting, some of you are good mind readers :). Upon further searching things became clear to me. I think?

G.L.

Hello everyone,

Looking to add components from 3D warehouse. Architectural, etc. Can't seem to find them. Have searched this forum, found some about wood grains.

Looking for building...

Michael,

The problem I was having had to do with the travel of the lift. I had to exert lot of pressure to engage and move the lift. The lift would also get stuck, jammed at the bottom end of...

Hello All,

Wanted to thank Rich Hummel for his prompt response to the issue I had with my lift. After talking to him and sending the lift to it was about a week when I got it back. Problem...

Please cout me in.

Thanks,

G.L.

Bob & Doug,

Yes, the wood was acclimated for two weeks before laying it down. Did not check with moisture meter, could have been worth the while, to eliminate the moisture issue. At this point...

Thanks for your suggestions. The T&G fit find, did not look at the width of very close when I bought new flooring.

Steve, I was thinking I could something along does lines.

G.L.

Need help.

Repairing flooring, new flooring is just a bit wider than existing floor. Did not catch this until laying a few rows. Have not nailed, yet. The difference is effecting the fit.

To...

Thanks for all your comments.

I modified the plans from FWW, made it bigger and did not use the open base. Will be adding drawers, shelving and DC in the future.

Used 2 pieces 3/4 mdf with...

This is my "first" real project. I want to thank everyone here for sharing their experiences and knowledge. This forum has helped me so much and will in the future.

G.L.

Rich,

Thank you for your response. It is very comforting that there is customer service given by companies like yours.

Will call in the next few days.

I was not trying to stir negative view...

Hello Everyone,

Bought the lift from Woodcraft. Now that I finished the RT table, started using the lift. Then out of nowhere the lift gets "stuck".

When I try to engage the rod it will not...

Here is what I did to make the bit I have work. Using the suggestion to remove set screw, but replaced it with one that gave me the clearance to trim the laminate.

Thanks again for all the input...

Will pursue some of your suggestions. Will report back. The bit that I have, from tip of set screw to top of bearing, is slightly bigger than the depth of router plate recces.

Thanks for your...

I used 3/4 MDF and laminated to pieces, pretty stout 32x43. Cut out plate opening first. Then laminated the top. When I trimmed the edge of top had one little spot where the laminate was chipped. I...

Building a router table. Having an issue trimming laminate around the router plate opening. Trimming the recessed area where the router plate sits, which is 3/8" deep, the bit I'm using does not give...

Allow me to "review" these saws. Gathered the info from their respective sites. Just comparing to help on decision to buy a miter saw.

Jet
RPM- (no load) 4200
Soft Start- could not determine...

Ray,

Thanks I will check HD.

G.L.

Garth,

Great! Looking to hear your opinion on the saw. Would like to see the Milwaukee in person before buying, but no one has it locally.

G.L.

Garth Welcome,

If you look down a page or two, I posted links to the Jet 12" and Milwaukee 12" sliders. I have not seen any reviews on the Jet. Fine Home Building had one recently on miters but...

New to WW, looking for thoughts on these saws. Prior searches here people like the Makitas. Have not owned a miter saw.

http://woodworking.jettools.com/Products.aspx?Part=707120
...