The wheels are coplaner.
Attached are some photos with the table removed.
The blade is tensioned.
The saw is a Delta 28-276
309679
Lower thrust bearing ass'y
309678
Upper thrust bearing...
Type: Posts; User: larry cronkite; Keyword(s):
The wheels are coplaner.
Attached are some photos with the table removed.
The blade is tensioned.
The saw is a Delta 28-276
309679
Lower thrust bearing ass'y
309678
Upper thrust bearing...
Do you read my post?
It is not the table. The thrust bearings are independent of the table. The blade is too far to the right with the table removed.
I am having this same problem except the blade is riding so far to the right that it barely touches the upper thrust bearing and completely misses the lower thrust bearing.
This seems to have...
Needed some 3 inch swivel casters for a small project. I usually use locking casters but that wasn't a requirement for this job.
Went to Northern Tool today where I found these casters for $4.99...
As I said I have built and installed 34 of these drawers and I am aware of the tabs.
In full extension on these 2 drawers the tabs will not release the slides.
Building some new cabinets for the shop and using 22" full extension ball bearing slides on the drawers.
I was removing the drawers in one of the cabinets to install drawer fronts and could not get...
More info here:
http://www.woodstore.net/motoca.html
It's also available in Wood Magazine's "How to Build a Great Home Workshop" book.
Anyone built one of these?
Anything you would do (or did) different?
207074
A Modern Rube Goldberg:
http://wimp.com/woodworkingproject/
Thanks for all your suggestions.
I made the cuts by placing a straight edge along the raised table saw blade and drew a pencil line on the left side of the blade from the front to the back of the...
I am trying to cut a trapezoid (6-3/4" at top and 14-1/2" on the bottom) on an 18-1/2" long piece of plywood. The angle figures out to about 12 degrees but my question is how I can safely cut this...
I recently purchased the SMC Vol 1 & 2 DVDs.
Lots and lots of files.
Is there an index available that would make it easier to find items on interest on the DVDs or am I missing something obvious?
Yeah - But as Steve Martin says, "I'd hate to paint it!"
it's working
I have enjoyed watching the old re-runs of NYW and especially seeing Norm without the gray.
I have been unable to get the video to play on the latest episode (Turned Post Bed). I've tried it on...
Thanks. That's more what I'm looking for. I did a search on McMaster-Carr's site earlier but couldn't pull up that info.
I'd still like to know the info from the magazine article.
I looked at those, that's not it. There are a number of sites that show something like this at Amazon but no dimensions are given or if they are provided it's not what I'm looking for.
...
I downloaded a Woodsmith Magazine article on pegboard storage. The author used 5/32" dia X 1 3/4" long L-hooks instead of regular pegboard hooks. The downloaded article does not list the source for...
I used a piece of scrap wood (2 x 7 x 3/8) and imbedded 2 rare earth magnets on one side and drilled a hole in the middle for the knock out bar. It fits on the ways just outboard of the motor.
Used the foam for some time but it was very unwieldy and a pain to find a place to store it.
A tip that I have used with good results.
Instead of saw horses use 2 or 3 large Rubbermaid (or any...
And of course the fun begins when you install known square cabinets and the walls you install them on are not square!
I've been using Scott's "Rags in a Box" for some time now and they really work great.
I fold them twice the long way and then once the other way and that makes an eight layer 6" by 2 1/2" applicator...
I use the excuse "I've had a nap since then" to cover all my forgotten tasks that SWMBO lays out for me and to explain the missing tools, hardware and other items that seem to move themselves around...
What do you Creekers do to watch all those woodworking DVDs you have?
I have a Magnavox 14" DVD player that weighs about 22 lbs and is presently taking up valuable bench space. I'd like to mount...
I built my air cleaner into a multi-purpose cabinet on casters with many many 1" holes in the top and put in an auto-shutoff timer switch. I use the air cleaner cabinet as a sanding station, assembly...