Look around I was able to buy it a lot cheaper locally than on the net. Also you get a person to deal with problems also.
Type: Posts; User: Jason Sanko; Keyword(s):
Look around I was able to buy it a lot cheaper locally than on the net. Also you get a person to deal with problems also.
18V Rayobi cordless brad nailer staple gun. Won't drive staples near as well as my stanly hand powered jobber and definatly won't do brads. Leaves brads about half way not driven and can't even...
So I know most of you guys hand hone your stuff. But has anyone have any experience with this machine? Wood Mag. did a sharpening system review a while back and this was the next best to the...
Fellow Kitsap County resident I wanted to say thank you. I was doing some mortises through and through and was trying to figure a way to make the corners really crisp. Well today I read the hand...
Probably the wifes car, but I would like to have my boat in there instead of under the car port where it is at now (I park my boat at the in laws all ready). It has been a sorce of contention about...
Guess I should rephrase it. There a a couple essential machines I am tired of moving around. I will not move my Tablesaw in the next shop at all, as well as my jointer. The Tablesaw will be the...
I bought all mine as needed and I am not done. I would not just go out and spend money on clamps or anything else untill I need ot for a project. $1000 goes a long way and you would be awfull...
I made these two for my TS and BS. To do it again in my new shop I will not have any mobile bases I hate having to move around and reset up my tools.
...
Take a look at the Delta also. I personally feel the closed base more top end
Mine was made in 1953, been refurbished by me. Newly rewound original (with original tage still hangin on it) 1953...
I thought you were supposed to use a SCMS with a push stroke cut (extend out to you, plunge down into work piece and then push away from body), and with a RAS a pull cut. I know I have never done...
Here is a better shot of in progress pictures of my "new shop cabinents. Need to get the bench painted also, but want to start finishing one side of garage first. I am in the middle of sealing and...
Hopefully the cabinetnts mantioned above will solve some of my "clutter" problem on my other cabinants. I built these from the Wood magizine article in the Shops annual issue from a couple years...
Here you can see the leveling bolts used. Yes the is an older vernable PC 690 router. Just can not part with it. Bought a second plate also. Am going to be purchasing the "big" PC after the...
Another view of it as viewed from the working side. The top is made of 3/4" Baltic Birch with a top and bottom of 1/4" hard board. I edge banded with oak to match mobile bases and laminated top and...
The extension is lag bolted to the cast iron wing. 4-5/16" X 1 1/2" secure it to the wing tightly. Prior to doing that the wing was precisly leveled with the entire top. I drilled and tapped the...
Here is fitup following routing out for the plate. Woodpeckers plate and I bought the template to do it. I love the plate.
Ok two parts here.
1. Finished my routert able extension and moving my fence on my Craftsman 22114. Came out well I think. I got the laminate in this week and finshed here up. First picture is of...
I would second the don't use the ramps. Looks like from the length:
a: They could bow enough to break one then you drop saw.
b. I load an ATV on ramps and it has four wheels and is...
It was off because I was cross cutting with the ZCI. I have a ZCI with an installed 1/8" splitter in it. I am bad about the guard though I will admit that. But I do wear a full face shatter proof...
Marshal it runs the entire length of the fence. All four stock bolts go from the fence through the angle iron and bolt to the top for maximum support. At the unsupported end (the right side looking...
I would not say my "factory" inserts never get used. They are very helpfull in routing new "zero clearance" inserts. BUT that is the only thing they do get used for.
Through bolt it with washers for maximum load distribuion on the top. Cast iron is brittle even to a 1/4" thickness. It does drill nice, like said above use a lubricant. I use common WD-40 when I...
Ok when I signed up on here I messed up and did it at work and at home. At work I did not think it worked we were having server problems that night. Anyhow now I have two profiles and want to use...
Router wing in progress. Need to cut down myu red laminate still and attach and band with Oak. It is a Woodpeckers plate for the PC 690/890. Made it of two pices of hardboard laminated to a pice of...
Support for front fence so it does not bend or sag with weight of fence.