Search:

Type: Posts; User: Ken Kortge; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds; generated 17 minute(s) ago.

  1. These go between the sander's pad and the Xtract...

    These go between the sander's pad and the Xtract sanding disc to make the sander's pad last longer.
    https://taytools.com/products/3m-random-orbital-hook-and-loop-protector-pad?variant=31997924900951
  2. Replies
    10
    Views
    1,079

    Check the manual - page 11. Your sander...

    Check the manual - page 11. Your sander apparently comes with a punch plate that should be used to punch holes into the the 1/4 sheet pad sandpaper after it has been installed. It's not clear to me...
  3. Lisa, I am in the process of moving my...

    Lisa, I am in the process of moving my woodworking from imperial to metric. My reasoning was that none of the lumber or plywood is dimensionally as labeled anyway, so I have to measure and/or cut to...
  4. Replies
    28
    Views
    3,962

    If you need more length, you can buy another 64"...

    If you need more length, you can buy another 64" extruded table and connect it using a Best Fence Male to Male Connector and a FastCap Upper Hand stand.
    https://youtu.be/e7CvDKRK-G4

    They also...
  5. Replies
    13
    Views
    2,005

    Honestly, that dado glue joint is going to be...

    Honestly, that dado glue joint is going to be VERY strong without using screws. If you don't want to clamp while waiting for the glue to dry, use brads to pin it together.
  6. Replies
    28
    Views
    3,962

    I recently invested in the FastCap Best Fence D4...

    I recently invested in the FastCap Best Fence D4 with the flat extrusion for my Dewalt miter saw & Dewalt miter stand. Not cheap, but so far I think it'll be good for my needs....
  7. Replies
    4
    Views
    1,099

    The Bourbon Moth YouTube guy uses playing cards,...

    The Bourbon Moth YouTube guy uses playing cards, and keeping track of the number of cards for consistency.
  8. A rule of thumb that I've seen: Set the depth of...

    A rule of thumb that I've seen: Set the depth of cut for each pass to no greater than the diameter (width) of the router bit. Some suggest setting the depth at increments of 1/2 the diameter.
  9. Replies
    5
    Views
    703

    The Kreg Concealed Hinge Jig, which does a very...

    The Kreg Concealed Hinge Jig, which does a very nice job of drilling the cup and pilot holes, matches the Blum requirements for the hinges I was using, but carefully check the specifications for the...
  10. Replies
    16
    Views
    2,980

    With no intention of hijacking this discussion...

    With no intention of hijacking this discussion ...

    If not using a dado stack and using a router instead, can you give a brief indication of how you use a router for dados & rabbets? I'm especially...
  11. Maybe a Bosch PS-21 12 volt driver. It has a 1/4"...

    Maybe a Bosch PS-21 12 volt driver. It has a 1/4" hex, variable speed, and variable clutch....
  12. Thread: Track Saw?

    by Ken Kortge
    Replies
    63
    Views
    12,408

    The Eurekazone.com tracks are self-aligning due...

    The Eurekazone.com tracks are self-aligning due to their dovetail shaped channels. Tracks are connected using two side connectors, but for lengths longer than 108 inches use of an additional center...
  13. Replies
    14
    Views
    2,307

    After looking at the website for a while I don't...

    After looking at the website for a while I don't have a clue what the device is supposed to do.
  14. Replies
    54
    Views
    5,603

    If you can, I highly recommend ditching the use...

    If you can, I highly recommend ditching the use of Philips head screws in favor of Torx (star) head screws, or even square (or Robertson) head screws. Soooo much better!
  15. Replies
    40
    Views
    9,530

    I prefer using the 64" track for cutting half...

    I prefer using the 64" track for cutting half sheets, so I prefer a 64" + 52" combo. It provides a nicer "launch pad" for the saw.

    I unsuccessfully searched online for a picture of the 8 foot cut...
  16. Replies
    40
    Views
    9,530

    I can only speak for the Eurekazone.com track...

    I can only speak for the Eurekazone.com track system that I use. The so-called Smart Base is attached to the bottom of a circular saw by pressing the saw blade against a row of plastic blades, and...
  17. Replies
    40
    Views
    9,530

    If you already have a decent circular saw, the...

    If you already have a decent circular saw, the Eurekazone.com system can get you a 64" track with a conversion base, two anti-chip edges, and two clamps for $155 (plus shipping).

    You can get a...
  18. Replies
    40
    Views
    9,530

    All I'll add is that track saws with an anti...

    All I'll add is that track saws with an anti chipout feature provide a much cleaner cut edge than that of a typical circular saw.
  19. Consider if the model you buy will take common...

    Consider if the model you buy will take common blades. I a the corded Bosch, but in hind sight I think I should have purchased a cordless version (I'm pretty much locked into the Bosch cordless...
  20. Replies
    15
    Views
    1,636

    I recently built four 12x12 foot horse stalls...

    I recently built four 12x12 foot horse stalls using something slightly less than 1000 McFeely's #10 promax 2-7/8 inch nocorode square drive flat head screws, and I didn't have a single screw strip...
  21. Replies
    42
    Views
    7,756

    They may have some restarting pains. I wouldn't...

    They may have some restarting pains. I wouldn't be surprised if product is slow to restock due to Covid. Recently I was surprised that my local hardware store could not restock washers - of all...
  22. Replies
    42
    Views
    7,756

    You might try calling them.

    You might try calling them.
  23. Replies
    9
    Views
    1,454

    Remember that rodents are your enemy. One mouse...

    Remember that rodents are your enemy. One mouse setting up living quarters in the trunk will destroy just about everything - even helmets.
  24. Replies
    42
    Views
    7,756

    I notice that the UEG isn't listed on the new...

    I notice that the UEG isn't listed on the new site.

    Mike Goetzke, how do you make sure that the UEG fence is parallel to the blade?? Just careful measurements?
  25. Replies
    42
    Views
    7,756

    Jim Dwight, have you been able to directly...

    Jim Dwight, have you been able to directly compare the "cut quality" of your track saw with that of an EZ Smart track system that uses a circular saw?

    The EZ Smart track system uses anti chip...
Results 1 to 25 of 161
Page 1 of 7 1 2 3 4