I could post pics but they would show absolutely nothing. Everything is intact and in its place.
For some reason the worm gear simply does not want to rotate easily enough when engaged with the worm...
Type: Posts; User: Gregg Feldstone; Keyword(s):
I could post pics but they would show absolutely nothing. Everything is intact and in its place.
For some reason the worm gear simply does not want to rotate easily enough when engaged with the worm...
What myself and Paul are saying is that the shaft does not rotate after tightening the front knob and of course making sure the locking screw is loose. This means there is no fine adjustment. Just...
Todd could you tell me if you are able to use the lever to do a fine adjustment of the height by rotating it on my machine? I cannot rotate the lever if the knob is tight in the front like they say...
Todd, can you tell me what is your experience doing the fine adjustment on this machine? The manual states that rotating the lever actually raises the bed up and down but I find all that does is move...
1
Gregg Feldstone
https://sawmillcreek.org/images/statusicon/user-online.png [OP]Member
Join DateOct 2006LocationUSAPosts329
Worm shaft problem : powermatic 60HH jointer
Just picked up this jointer used in very good condition. I’ve never had a jointer with a lever to move the bed.
I can make rapid gross adjustments by pulling up and down but turning the shaft...
Just picked up this jointer used in very good condition. I’ve never had a jointer with a lever to move the bed.
I can make rapid gross adjustments by pulling up and down but turning the shaft...
I got an Albrecht 1/32"--1/2" chuck for mine. The Llambrich were hard to find and actually more expensive.
The table does no completely lock at 0 deg. unless I tighten the big attachment bolt so much that I can't even tilt the table. The locking pin is a bit smaller than the hole it goes into and thus...
So thereÂ’s also a pm 1150 Drill, 2 walker turner bandsaws One is to Speed, pm 35b sander, walker turner Benchtop drill,
pm tablesaw,
anyone ever had the 1115 drill. I just bought a 2820 and...
A slightly used Powermatic 60 HH 8 inch jointer with mobile base is available at an estate sale this weekend. The seller is allowing me to place a deposit on it before the sale. I am simply waiting...
Additional Picture
Advertised as a Stanley bedrock 605 C type six. I read that 605C was only type one through four and has three screws in the frog. Seller claims he refurbished but has original japanning. It looks...
Thanks for everyone’s replies. I have learned a lot but unfortunately there was a line waiting to get into the sale before it opened and I was unable to be there because I had to work. I showed up...
They are also selling these clamps at the estate sale. What are they for and what might I offer for them? Thanks
I may go to an estate sale which appears to have some nice planes. I think what I’m looking at is a number seven or number eight jointer and may be a number five bench plane and may be a #4 smoother....
Thanks for everyone’s reply. I was afraid you guys would tell me what you have. The buffer is a general purpose high-quality Baldor machine that’s used mainly for metal buffing and polishing. It does...
They are asking $650 for the machine and yes I realize that is the bellows. They said it runs OK and are supposed to send me a video. I’m just not sure about spending that much for a 36 year old...
I have the opportunity to buy a Hegner polymax three scroll saw made in 1986. I will attempt to show a picture of it ,which in my opinion shows the machine in great condition except for that the...
I recently got a decent deal on a high-quality three-quarter horsepower 8 inch buffer.
I would like to leave it set up for Turning and other small wood projects. my grinder is low speed but I want...
I wish I had bought the lift lock and roll mobility device which apparently is not made anymore. Does anyone know where I could get one or have one to sell? I need it for my PM 3520 B
Can can you please send me the PDF? I’d like to try this for my 3520
Just wondering if anyone else has come across this website: bilibears.com.
The prices are obviously incorrect so I am wondering if it is just a total scam or what?
Why can’t birch plywood be made to the same specifications as Baltic birch wherever birch is grown and milled? you would think the Chinese and other Asian countries would want to start producing a...
I also ran across a thread of people reviewing the grinder on Amazon. One person mentioned that Jet told him to install a GFPE. I am not sure if they meant a GFPE breaker or a GFPE receptacle, if...