[OP]
Contributor
After about 4 min. into the last job of the day the laser stopped firing. Checked the lense and found it dirty. After cleaning the lense and mirrors I restarted the job and after about 30 seconds it stopped firing again. Checked and cleaned the filters just in case, no help. I think the tube gave up after only 8 years and 8 months! Can't think of anything else that could cause the problem, any suggestions?
This is a ULS M300-50 and has given superb service till today.
Dan Hill
Member
Do you have a magnetic switch for the door that could be opening? That would shut the beam off.
Epilog Helix 45W w/Rotary, Corel 12, PhotoGrav
Contributor
Eh? In human years, that's about 110.Originally Posted by Dan Hill
(Although normally I wouldn't expect a failed tube to be intermittent.)
Yoga class makes me feel like a total stud, mostly because I'm about as flexible as a 2x4.
"Design"? Possibly. "Intelligent"? Sure doesn't look like it from this angle.
We used to be hunter gatherers. Now we're shopper borrowers.
The three most important words in the English language: "Front Towards Enemy".
The world makes a lot more sense when you remember that Butthead was the smart one.
You can never be too rich, too thin, or have too much ammo.
[OP]
Contributor
It fires corectly for about 30 - 45 sesonds so I don't think the mag switch is the problem. If the door opens while the laser is running it stops and returns to home position. If the door is not activating the switch when the laser is started it will turn on the red pointer and go thru the motions.
Make sure the tube or the power supply are not overheating...
Hi-Tec Designs, LLC -- Owner (and self-proclaimed LED guru)
Trotec 80W Speedy 300 laser w/everything
CAMaster Stinger CNC (25" x 36" x 5")
USCutter 24" LaserPoint Vinyl Cutter
Jet JWBS-18QT-3 18", 3HP bandsaw
Robust Beauty 25"x52" wood lathe w/everything
Jet BD-920W 9"x20" metal lathe
Delta 18-900L 18" drill press
Flame Polisher (ooooh, FIRE!)
Freeware: InkScape, Paint.NET, DoubleCAD XT
Paidware: Wacom Intuos4 (Large), CorelDRAW X5
Member
Dan,
I think you may be correct in your assumption regaurding the tube
However, welcome to the club
Bruce
Moderator
When my first tube failed it cut broken lines, fired on and off randomly. If you use it regularly I'd say that you got your money's worth out of it.
Sammamish, WA
Epilog Legend 24TT 45W, had a sign business for 17 years, now just doing laser work on the side.
"One only needs two tools in life: WD-40 to make things go, and duct tape to make them stop." G. Weilacher
"The handyman's secret weapon - Duct Tape" R. Green
[OP]
Contributor
I agree with Joe, the tube dosen't owe me anything. The unit saw an average of 30 - 35 hours a week for more than 8 years.
Dan
Member
My M-300 50W machine is 6 years old and never missed a beat until last year. A call to Universal and they had me move a couple of switches on the tube and it has been running fine since. They said it increased the tickle on the tube and that the tube might go anytime now. The problem only showed up when the temp in the shop was below 65*. If the shop was warmer, the problem did not show up. The has run perfect even in 65* temp for the past year and it ran just fine this morning at 66*.
I checked on tube costs and I recall about $1200 for the 50W.
Trotec Speedy 300 45W
Universal VLS4.60 50W
Universal M-300 50w
ShopBot PRSAlpha48
Techno LC4848
Oneway 2436
Posting Permissions
Reply With Quote
