Needed....sanding wheel for 12" table saw

[dirk martin]

I need one of those sanding discs that turn your table saw into a disc sander.
12" Jet saw, with 1" arbor.
I know they exist, but I can't find them.
Can someone help?

[dirk martin]

Sometimes, it's just too simple.
Someone told me I already have one.
Just glue sand paper to the side of an old 12" blade.
And, grind the teeth off, if they bother me.

[Larry Browning]

Wouldn't that spin too fast? I have now knowledge of this, it just seems like it would be a problem. I have a shopsmith and the rpm is supposed to be much slower for the sanding disk than the tablesaw.

[Charles Taylor]

Using an old blade with the teeth still attached doesn't sound like the best idea to me, especially if you're going to have your hands near it. Even grinding them off will probably leave an irregular edge that is nearly as capable of some serious harm at that speed.

[Duane Meadows]

Have to agree with Chuck. Here, try this...

http://www.forrestsawbladesonline.co..._or_Table.html

[Bruce Wrenn]

Get a 12" steel plywood blade, mount it in the saw backwards. Turn saw on, and use angle grinder to remove teeth, and radius edges. Be sure to clean ALL saw dust from saw before starting, plus turn off dust collector.

[Frank Drew]

Why not a circular piece of plywood with a one inch hole drilled in the center?

[dirk martin]

Hmmmm.
I do have a 16" lathe. I could easily make a round piece of plywood on that.
Circular plywood sounds reasonable. I doubt it will flex under slight pressure.
I'll be sanding segmented 1/2 rings.

[Joe Kieve]

Since you have a lathe, just mount sand paper to the disc on the lathe. You can vary the speed to whatever you need.

[David C. Roseman]

I'd second the use of your lathe for this. It can be done on the TS, sure, but I wouldn't want abrasive sanding grit down in the innards of my saw. Or even on the cast-iron table.

David

[dirk martin]

Since you have a lathe, just mount sand paper to the disc on the lathe. You can vary the speed to whatever you need.

Yes, but it's critical that the wood I'm sanding, be exactly 90 degrees to the sanding wheel. With the table saw, I simply lay the wood on the table top, and bring it into the sand paper.
On the lathe, I don't have such a flat table....

[Duane Meadows]

Yes, but it's critical that the wood I'm sanding, be exactly 90 degrees to the sanding wheel. With the table saw, I simply lay the wood on the table top, and bring it into the sand paper.
On the lathe, I don't have such a flat table....

This will solve both problems... keep the grit of your saw and sand square.....

http://www.grizzly.com/products/12-Disc-Sander/G7297

I know it's a tad more expensive , but... not as much as ruining a good tablesaw!

[Bill White]

I'd be a little spooked by a plywood wheel spinnin' at table saw speed.

[Erik Loza]

I'd be a little spooked by a plywood wheel spinnin' at table saw speed.

Ditto, the speed would be my concern. We used to sell sanding sleeves for shaper spindles and you had move the belt to the slowest speed on the pulleys to make that anywhere near useable. Not telling anyone what or what not to do, just sounds sketchy to me. Personally, I would rather use an actual disc sander and then create an extension table or something like that.

Best of luck, whatever you end up doing.

Erik Loza
Minimax USA

[Michael W. Clark]

Yes, but it's critical that the wood I'm sanding, be exactly 90 degrees to the sanding wheel. With the table saw, I simply lay the wood on the table top, and bring it into the sand paper.
On the lathe, I don't have such a flat table....

There was a plan in FWW for a rest to set the work at the appropriate angle on the lathe.

I have a Delta 12" disk sander that I dont use if you are interested.