Very nice. I don't suppose there is a set of plans for this floating around out there? I am afraid however, if my cabinet saw sees me making this a fight may ensue.
Very nice. I don't suppose there is a set of plans for this floating around out there? I am afraid however, if my cabinet saw sees me making this a fight may ensue.
Sweeeeeeeeeeet!
I am never wrong.
Well...I thought I was wrong once...but I was mistaken.
Thanks for all the great complements!
OK here's the plans I made to make the saw bench from and cut list. As I mentioned in my first post my saw bench ended up shorter than the plans called for. What happened was that I figured a 6" overhang at the ends was a bit much and made a change but somehow screwed up something and well mines ~45" long with a 4¾" overhang.
You will want the vertical leg parts to be sized for your comfort. Had 2" tenons on each end but trimmed down later.
I didn't try for any thickness, just made sure all was flat, square and the same.
Enjoy, post pictures please!
saw bench plan.JPG
Last edited by Judson Green; 10-19-2013 at 12:59 PM.
My worry is if the bench is too low the saw might hit the floor or the feet going across. Just have to be careful at those points.You will want the vertical leg parts to be sized for your comfort.
One thing that might also help is dog holes positioned to guide the edge of the work piece to keep the kerf over the slot whilst sawing.
jtk
"A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
- Sir Winston Churchill (1874-1965)
If I am doing one rip of about 2 - 3' and the band saw has not been set up for the day, it is almost as fast to just rip by hand.But I'm not gonna be selling my bandsaw.
If the band saw is set up for use, then they get ripped on the bandsaw.
For long rips, it is difficult for with my 10" bandsaw to cut long pieces. Partly this is due to my bifocals and partly due to the difficulty of guiding a long piece.
The way my wimpy bandsaw handles some hardwoods, it is faster and ends up with a better kerf to rip by hand.
jtk
"A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
- Sir Winston Churchill (1874-1965)
Excellent job. Adding a rip slot in mine was the best improvement I made to it. I couldn't believe the difference from ripping on the side of the saw bench to ripping with the board supported on both sides of the cut. Rip cuts Can be made without clamps now.
Good, Better, Best never let it rest
until your Good is Better and your Better is Best
Member of M-WTCA Area D
Last edited by Judson Green; 10-19-2013 at 2:40 PM.
I have one, but don't have any bits for it. I think it attaches to a drill press a friend gave me with the mortiser. Haven't set up the drill press either since it is a second one.Like for mortising, I have a hollow chisel mortiser but I feel it would cheatin so its stashed under my bench.
jtk
"A pessimist sees the difficulty in every opportunity; an optimist sees the opportunity in every difficulty."
- Sir Winston Churchill (1874-1965)
Beautiful work. A bit up market for me though.
Sketchup plans for a similar bench:
http://www.billyslittlebench.com/1/p...-sketchup.html
At the risk of completely hijacking this thread (sorry, Judson!), here's what I'm planning to build now. I modified the "traditional", slotted wedge saw bench to something more akin to this twin platform style with a full length slot down the middle. Although that means I will now have to rip a nice piece of ash I had designated for the top, right down the middle (without the use of a good saw bench, of course).
I'd be interested in thoughts from Creek members on my design since I am a complete novice in this area. I'm looking at using common pine for most of this (with the ash top pieces as I mentioned), but am thinking of using poplar for the lower support end pieces since they have the bulk of the load to carry. I'm not too crazy about the angled tenons and their ability to handle loads, that seems to be the weakness of this design but I don't want to add more feet.
Andy