Sawmill Creek Woodworkers Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Chinese laser purchase/Shenui/Laserworks tips and tricks thread
Thread Starter: Rodne Gold
Considering a lot of us are going or have gone that direction , I thought it a good idea to combine our knowledge pool in one thread. So I have started one. Those of you that have already posted to other threads can perhaps repeat and consolidate the posts here or at least point to other posts on...
Last Post By: Hermes Sandoval Today, 12:57 PM

Is CBN simply worth the extra cost?
Thread Starter: Matt Mackinnon
I knew from the start that getting into woodworking was going to be a very expensive hobby. And even more so when I took up turning. I recently bought a whole lathe setup with a wolverine jig and grinding wheel. The fellow who I bought it from had 2 oneway blue 8" grinding wheels in 54 and 120...
Last Post By: Steve Fulgoni Yesterday, 10:44 PM

cyclone selection-- Onieda, Grizzly, or Penn State
Thread Starter: Don Jeansonne
I have come the conclusion that I need to upgrade to a cyclone with 3hp min size. I am looking at Onieda V3000, Grizzly G0441, and Penn State 3.5hp. The cost differences are not that mush with Penn State being lowest. I would like to know people's opinions about the pros & cons of these suppliers....
Last Post By: James White Today, 5:24 PM

Laser Engraving True 8bit Shades of Grey
Thread Starter: Jeff Woodcock
Hi everyone, I'm new here and this is my first thread and post on this forum. I would like to introduce to everyone a new process me and my son developed to laser engrave true 8bit shades of grey using a 445nm laser diode. There is no dithering a image first, no pulsing or overlapping dots to...
Last Post By: Jeff Woodcock Today, 6:08 PM

Memorial day must be coming....
Thread Starter: Jeff Monson
Unleaded went from $3.79 this morning to $4.09 in a matter of minutes. 30 cents is quite a hike, cant tell me the gas stations aren't smiling for a couple days.
Last Post By: Brian Elfert Yesterday, 11:26 PM

Buy versus build?
Thread Starter: Jamie Buxton
Because we're builders, we can make stuff for our shops. We also have manufacturers which are happy to sell us similar stuff. For instance, you can make your own sawhorses, or you can buy them. You can make a workbench, or you can buy one. You can make your own jigs (for instance a shelf-pin...
Last Post By: Darius Ferlas Today, 6:27 AM

Martijn Bouwman

There is no available content written by Martijn Bouwman

Recent Polls
Please Select The Bailey Box Contest Winner (148 Votes)

Bill Wyko (84 Votes)

Craig Matheny (6 Votes)

Dick Bipes (33 Votes)

Hayes Rutherford (12 Votes)

Jacques Malan (3 Votes)

Kathy Marshall (3 Votes)

Matt Mitman (7 Votes)
Recent Forum Posts

Welder outlet question

My recommendation would be use the plug on the welder to guide your size of wire to the receptacle. OSHA would frown very heavily and expensively on anybody
Phillip Gregory Today, 6:56 PM

Outdoor beam glue

Pulling up the boards with a rope really isn't an option. I don't have direct access down to the street below, I would have to crawl out to the edge of
Greg Forrest Today, 6:50 PM

I made the switch...

Unfortunately my size/tpi combo is really rare (and old) - near as I can tell, the head & tail stock are from about 1880. Still working well though
Olaf Vogel Today, 6:45 PM

Walnut slab sources in Los Angeles (could be mail order as well)

I would like to get back into woodworking and start working on a new dining table. I would like to use book matched slabs (two pieces) to make a table
Frank Martin Today, 6:40 PM

Need an idea fast

Psalm 46:1...

God is our refuge and strength, an ever-present help in trouble....
Dan Masshardt Today, 6:40 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Martijn Bouwman

Recent Polls

Recent Forum Posts

Recent Blog Posts