I use epoxy on joints of chairs that I build and it works great. For $25 you could buy more than enough two part epoxy with a 24 hour cure time. I mix in sanding dust to color it, but I have also...
Type: Posts; User: Angie Orfanedes; Keyword(s):
I use epoxy on joints of chairs that I build and it works great. For $25 you could buy more than enough two part epoxy with a 24 hour cure time. I mix in sanding dust to color it, but I have also...
Get the kind of gear puller that has fingers that would hook behind hand wheel and push on center shaft. HF had them.
Matt,
My prayers are with you. May God bless you and your wife to good health.
Angie
As Rich said, V Carve Pro can only accept 2D drawings/vectors.
Angie
V Carve Pro will do everything you need if all your work is 2D. You can also use the free 3D machinist program and use preprogrammed 3d models. If you want to be able to model in 3d, or import a...
Flowing, alive, and beautiful. Great work.
Angie
Yes, abrupt turns such as 90's cause more pressure drop (loss of suction) than gentle sweep turns.
Thank you, Randy, for sharing with us your experience with Mr. Tashiro. Sounds like you were blessed to sit at the feet of a master.
Angie
All good advice. After you have done the upgraded insulation and checked your ductwork, you should consider adding a zone control damper and zone control board run from a second thermostat upstairs....
Depends on what you will use it for...
That machine sounds good on paper, however the 22 inch dimension makes it very narrow for general use. If you are making snowboards or skateboards, the...
I have Nema 23 steppers on my CNC router with rack and pinion drives, which provide about a 3:1 step-down in speed; see
http://www.cncrouterparts.com/rack-and-pinion-drive-nema-23-p-50.html
My...
Make sure you visit the bakery behind the Raleigh Tavern...as I recall good gingerbread men.
Angie
That is a masterpiece. Your level of craftsmanship and patience are amazing.
Angie
From my experience, maple is a real challenge to stain evenly. My recommendation is to use a Transtint dye in DNA. Spray light coats on a piece of scrap, to make sure the color is right.
Olive wood. Smells very different and very pleasant - like a sweet vinagerette dressing.
Jim,
Congratulations on getting the beast running. Looking forward to seeing it in person on Friday.
Angie
It is interesting to see various theories of static electricity being discussed. I join the camp of those who say there is only a tiny chance of a home system static discharge causing an explosion. ...
Thanks for the information, everyone. That helps calibrate my thinking.
Angie
I am planning on adding a third garage (14 ft by 20ft ) to use as a dedicated shop. It will have a garage door, brick exterior (three walls), insulated and sheetrocked, but no HVAC at this time...
I built a cut down version of Joe's Hybrid with a Cast CNC top end in order to fit into my limited shop (garage) space. The gantry is 48 inches across and the table sides are 60 inches long, which...
I am now on my third machine which is a Joes Hybrid with a CastCNC top end, and I like it a lot. I made my machine smaller so it would fit in my garage shop - the table is about 32 by 44. Also...
The classic book is "Constructing A Five String Banjo," by Roger Siminoff, available on Amazon.com. There is also a music instrument makers forum with a wealth of info (mimf.com).
leveler feet like this:
http://www.rockler.com/product.cfm?page=2053&rrt=1
I have the HF dust collector which I rearranged to exhaust (without filters) through a Thien baffle/can and then to the outside world. Very little makes it to the outside world. It has worked that...
Peter,
Best wishes for your wound and your pride to recover. Unfortunately, too many of us, including me, have done things that resulted in pain. My right hand is suffering from a hit it took...