Search:

Thanks for the reply Mr.Baker I did a search for killing the daubers B4 I posted here. Problem is,, catchin them "in the act" OR just flying around while I am out there.
When I do see any even...

:mad: Anybody out there know how to get rid of mud daubers :mad: ? My work area has a roof but is open on all but 1 side. I do what I can BUT There HAS to be some way to kill them lil' %$^#*s before...

I read the RAS thread that Jose did. I have an aux. end ond a RAS I bought at an auction, Through ya'lls help I also got the manual for it. (thanks to that I learned they are online on sears)
...

Mercy, now that is a serious bandsaw. Best of woodworking with it

Thanks anyway Ya'll I got lucky and finally made out the #

so I should get a base coat of paint? I was going to try and make my own color when I found out I had built my gazebo too close to a mulberry tree. But I ended up having to deal with health probs B4...

What type of finish can be put on cedar (I built a bench) so it will retain most if not all of its orig tone when it is outdoos? I finally found anexterior poly for OUTDOOR USE Unfortunately after 1...

I appreciate the replies, Now,,, time to get back to woodworkin again,Again Thank You

Long time no see ya'll
I bought a radial arm saw at an auction last week. I think its a 1977 model,but know its a craftsman brand
Opposite the blade side there is a male threaded rod that looks...

I put the name in the title so the mod. can delete it if its not allowable. I didn't see where it wasn't in the FAQ's
So here goes,,, Are Harbor Freight tools worth the money? I don't get to use the...

Thanks
Sorry I don't have a camera Basically tho all it is ,is a speaker inside a large cabinet. Yes I could get another speaker but when I was looking at them they cost 65.00 at a min. all the way...

didn't think about sandwiching the board,Thanks I'll gve that a shot

can a person glue the magnet back on a stereo speaker to get it to work again?
I have a Radio Shack Stack and the magnet came off one of the speakers. I asked the R.S. dealer but didn't get anywhere...

I did securly clamp the board to the fence,and made sure it was plumb when I cut it. I was looking at the bottom piece walla go and the 45s on it are just fine (no crown). Idunno what I did wrong to...

I appreciate all the answers ya'll give. I definately will be askin quite a few.Especially if and when I get my shop set up. As I stated B4
THANKS!!

Appreciate the info ya'll.

I'm trying to make a simple flag display for my brothers flag. When I cut the 45s they have a "crown" in the middle which won't allow them to fit snug. What's goin on? I'm using a chop saw,blade is...

anyone out there have a plan for a jig that will hold a belt sander? I had one but I can't find where I put the plan at.
Thanks

Thanks for all the help . Aftr I tried to scrub some of it off earlier with a non-scratch pad. I found out I have scratched it. SO long story short I just went and bought another sheet. LOL I'd been...

I been letting it soak in a tub of hot water Thanks for the help

how can a person remove the plastic covering off plexiglass? I have an older piece thats still good and the plastic overwrap has stuck to it and Im havin a heck of a time trying to remove it.

Thanks I appreciate it and will give it a try

Is Sketch up a draw program on here?

Is there a way to get batteries to re-take a charge? I have a Dewalt 9.6 cordless drill I've just got back and the batteries are dead They will take a charge but won't hold it very long.
I was told...

Hi ya'll I'm a newbie here and will have what sounds to be some dumb questions (now & later :rolleyes: ) I'll get the hang of it all hopefully soon. I been trying to feel my way around for a few days...