I got a 1 - 1/4" spindle and the router spindle that uses ER25 collets.
I'm a bit confused on the speeds. The chart on the side says it uses 4 gears, but when you take the cover off, there are...
Type: Posts; User: Bryan Hunt; Keyword(s):
I got a 1 - 1/4" spindle and the router spindle that uses ER25 collets.
I'm a bit confused on the speeds. The chart on the side says it uses 4 gears, but when you take the cover off, there are...
I also have the Airtight clamps from Mac. I use them all the time on my Hammer K4 slider. They were expensive, but they are built like a tank and worth every penny.
I finally got my Felder F 700 Z shaper. I've run a couple of boards through it, and so far, I absolutely love it.
A question for fellow shaper owners - what feed rate do you typically use on your...
I got our new 5 panel door for the master bedroom out of the spray booth and installed.
I filled some knots and cracks in the Hard Maple cornhole boards I'm working on for a buddy.
I started an...
I completed my new Roubo split-top bench. I used the plans from Benchrafted, but made it a bit wider and taller. The top measures 87" long by 29" wide. I set the height to 43". This was my firs...
My Christmas tool should be in Dallas by now and hopefully in route to me next week. I'll post pics when it arrives :).
Here, I'm fitting the wedged pins. There was a lot of hand fitting because holding an exact angle with a chisel in Hickory is not very easy.
487937487938487939
Finally, the finish. I sanded...
I added a chamfer with a hand plane to the tops of the legs.
487930
Now the glue-up. I only glued 1/2 of a side at a time because I was worried about the open time and getting all of the...
The sides were joined with though tenon and wedged pins. The narrower boards got vertical wedges while the wider boards got horizontal wedges. In hindsight, I should have gone will all horizontal...
One of the tenons was a bit challenging ...
487918487919487920
I clamped a block to the face and used it as a saw guide. I then used a combination of chisels and router plane to finish the...
The build started with 6/4 Hickory. The legs started as 8" wide boards that I ripped down the middle, book matched and laminated. One of the boards had a bad twist in it. By the time I got it flat,...
My youngest son asked me to build him a loft bed. I said sure, no problem. I figured it would't take too long. I was wrong! 340 hours later (translates to about a year - only working the...
Yep, I posted on Craigslist this morning :)
Bump - still available.
Bump - still available.
Still available.
I have Shiner Bock in the fridge. You are welcome to stop by.
Christopher, You are welcome to stop by and see my shop. I also have a slider you can check out.
Hey Kurt, I own a Hammer K4. If you have any questions about that specific saw, I'm happy to help.
I recently upgraded to a planer/jointer combo so I'm selling my Powermatic 15S with spiral cutter. It has a Wixey DRO and the blades were changed about a year ago. $2500. I'm in Leander, TX which...
I just upgraded my 8" jointer and 15" planer to a Felder AD941 16" planer/jointer combo. This thing is a beast. I'm fortunate to have a nice neighbor with a forklift. I ran some Hickory through it...
I know there are several threads on this, but I'm asking again because Tools for Working Wood and Lee Valley seem to not sell saw sets any longer. Does anyone have a resource for purchasing a...
I broke a handle for one of my Lie Nielsen chisels while chopping a mortise this weekend. Lie Nielsen is sending me a replacement at no charge. I've had my chisels a long time and this is the...
I got a VFD for my CNC spindle from https://wolfautomation.com. I went with a TECO Westinghouse model and have been very happy with it. There is a learning curve on programming the thing, but it is...
I just ordered from Spectrum Supply - way cheaper than BandSawBladesDirect.