Search:

To all that contributed to my sprocket questions. Thank you, all of you. And you won't believe what happened. I heard back from someone I contacted two weeks ago. He had told me that his...

I usually don't believe in miracles, but here is what happened. Last week I emailed everyone on Ebay that was selling older Delta/Rockwell planer parts. Everyone said that the item was...

Definitely metric. I know someone that says he can make one of these for me. We shall see.

I am looking for the out feed roller sprocket. Looks like this. 517456

I spent a couple days looking online, and no one on Ebay has even a used one. I was advised to contact Motion Industries.

517452

Check out around part numbered #166

That is the bushing, that block thing. It does have a oil hole right in the center of the indentation for the spring that holds the roller down. It all together slides up into the machine (without...

517445517446

After struggling for a long time with a LOT of back and forth and PB Blaster and more turning, and more back and fourth, and then lots of pounding to get it off the shaft. ...

I will open it back up and get a picture of all that stuff. But first I have to run an errand. Here it is without the chain and roller sprockets. More to come.517427

517419517420517422

Finally got it. YEAH!! Here is the sprocket and spring......and me.

The bushings on either end of the out feed roller are like blocks of metal with a hole bored out for...

517419517420

Finally figured out what I was doing wrong. So now I can. YEAH! :) Here is the sprocket and spring.

Bill, that first one you sent from Motion, looks really good. The plate with the model number says Rockwell-Invicta 22-650. I think I read that it was Brazillian made for Rockwell. 1984. I just...

What should I take pictures of? And when it says 06B-2-27, what does the 2 mean?

Yes, Motion Industries about 30 minutes away. Thank you everyone for all the support and encouragement. Sounds like there may be hope yet. Just noticed the way to add photos. I will take some...

The other sprockets are good, and the chain says 06B. I am not sure how to add photos. I am new here. What should I do to post some photos? I have been using the machine to plane about 30 1" x...

Nope, not the one. The one from Grizzly has more teeth. Looks like I might be out of luck. What a shame. The planer is worthless without that sprocket. I wonder why Delta discontinued all these...

Looking for some parts for a Delta 22-650 , that are no longer available from Delta. Sources?

Yes, Ron, that Grizzly part looks very close. I will call Grizzly tomorrow and get more details. Thank you for sending that. It is the closest I have seen so far.

I got the roller out. It would not turn by hand. I finally got it freed up with PB blaster and much persuasion. The shaft was slightly scored. I smoothed it off, and got it to spin again in the...

It is what is called a duplex sprocket. 5/8" bore with key, 27 teeth, 3 3/8" diameter. Thanks for the resources Bill.

Thanks Maurice, I followed the link you sent and found the sprocket, it says it's discontinued. Yes, it is sad, since it is a good solid machine. It was my fathers, he left it to me. I hope I can...

Hi Bill, Thanks for that great video. Well, I took the out feed roller out and I think I may have found the problem, even though I still don't know how it happened. One of the springs got bent,...

I have no idea why or how this happened. Maybe I fed a board into the planer before the previous board was out. I don't know. But here is the story. I realized the boards were not feeding into...

Thanks a bunch Rod. I did find one at McMaster-Carr. Their part number 6027K65. Less than $4.00. The chain is 06B, and uses an offset link. Then I found one believe it or not, on Amazon. Go...

Hi, I have a Rockwell RC-33 13" Planer. Last night it quit feeding and come to find out looks like I busted the master link on the feed roller chain. The part number for that is listed as...