Are there beveled edges on the stall matts? if not, does the edge cause a trip issue?
Type: Posts; User: Bob Johnson2; Keyword(s):
Are there beveled edges on the stall matts? if not, does the edge cause a trip issue?
Thanks Ron, for $8 I'll give it a shot.
I'm having issues with arthritis in my toe joints, seems to get exasperated on the days I spend hours in the shop. Would like to try a few mats, 3 around the workbench and 1 in front of the TS. I do...
Thanks folks, it gives me a couple solutions I can work with.
Looking for a bit of help building the buffet pictured below.
I've never built anything where the legs stand proud of the cabinet doors, does anyone know of a hinge that would provide more then...
I've used washers but knockouts from electrical boxes might work.
You could look at ash too.
Have you ever tried RV Parky?, it shows a few more or less close by. If it were me I'd try Johnson County Park http://www.jocoparks.com/johnson-county-park/ as I like public parks. There is a Lake...
Here's another that I've been sitting on, no pun intended. https://www.jakeschair.com/
I picked up these over the summer. https://smile.amazon.com/gp/product/B007JZCVAQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
While I agree with the others as to not seeing a reason to keep adjusting it, I don't remember the last time I've changed mine, and I change blades a lot. I do see a knob with 2" threaded 5/16"-18...
If you can't fit a contractors saw on a mobile base then a jobsite saw may be your only other choice. When looking at the $800 price you are factoring in the $200 dado set which you'll have to buy no...
The link in the 2nd post works. At least it does from Chrome.
I'd also turn the TS around as the door is on the outfeed side at the moment. I'd also check tool heights for clearance of longer and wider boards.
From the pic the Ultimate Table Saw Sled looks to use an awful lot of cut depth.
I use the MG unless the material doesn't fit between it and the blade, as in wider panels, and also for anything...
Don't know about iut being the best, but https://cutlistoptimizer.com/ is free and it works.
I looked on line at the WB'ed, looks like most folks don't care for it, have you used it?
Looking at the contact cement instructions it says the application temp range is 64F - 77F degrees, for safety you are supposed to keep the doors and windows open.
I have a few items to cover with...
FWIW... I've been putting in some time with my Dewalt, something that just came up is when running a thin kerf blade the blade moves during the cut. Did a few cross cuts and I can see the blade move...
Google "clamp rack". Each slot has just 1 bar clamp on mine although some hold more. I have 2 racks of 16ish.
Hanging on a nail next to the entry door to the shop I have roughly a dozen steel rulers, 12", 14", and 24", I also have 6 6 inchers that reside either in the apron or supposedly on a small table by...
I've got a set, from many moons ago. The coarse wheel is like a grinding wheel, works okay on something like a hatchet, the fine is pretty good to put a finished edge on knives and such although they...
About 2 months ago I went from a 3 hp Unisaw to a Dewalt dwe7491rs jobsite saw. I obviously don't have a lot of time with the Dewalt but here's my thoughts so far.
Added wing and an outfeed table,...
I've got a Dadonator, cuts well but the finish, or lack of, on the blades themselves is lacking. Need to keep them waxed or they corrode. This may have changed, my set is about 20 years old.
Left, right. Cause it just works that way.