I use them in my shop... Same as Travis, one Amflo, and one HF. Both work great! I once had the yellow coil hoses in the shop, but after using them for a while they don't seem to recoil so well. ...
Type: Posts; User: Adam Strong; Keyword(s):
I use them in my shop... Same as Travis, one Amflo, and one HF. Both work great! I once had the yellow coil hoses in the shop, but after using them for a while they don't seem to recoil so well. ...
I also use a HF DI in the shop and agree the tip makes all the difference. A clean/lube of the internals was needed on mine out of the box. I disassembled the workings and cleaned them (as a former...
I would not expect any type of adhesive patch to stick for long. The dust embedded in the fibers of the used bag would not allow a permanent bond. The only permanent way is to break out a needle an...
My method is very similar... Between coats I only sand if there is a visible high spot. I start with a 12 inch trowel and a thin mix and then do 2 additional coats at 18 and 24 inches with a medium...
I see no issue with the upward runs. As long as you use 6" pipe, keep your runs straight with limited sweeping turns, and utilize blast gates, the HF 2 hp DC should do fine. The upward runs have...
Another new thread brought me back to this one and I thought I'd post how it is all working out. After nearly 3 months with this setup, using the DC a few times a week, I don't notice any dust...
Check out these other two threads, they should answer most of your questions... Hope this helps!
http://www.sawmillcreek.org/showthread.php?p=1541059#poststop
...
I use various brands and styles of speed squares nearly everyday in various construction trades, but would never use one for more than rough carpentry and framing.
That looks like the result of the acid treatment... Not sure one coat of the clear will go on thick enough to fill the porosity and give a nice smooth sheen.
Another reason to vent thru the wall or roof and not use a filter.
I had that thought when figuring out my set up, and that is one reason the blower is not in my attic. This question could be answered by calling the manufacturer of your blower and asking the max...
If placing the DC in the attic, you certainly want the bag or barrel to remain on the shop floor, otherwise emptying would be a pain.
I have 10' ceilings in my shop and have the DC blower mounted...
I have a long history of having a hard time recognizing that option. :o
I am with you Phil... If a panel is rated for a tandem breaker and the breakers are code approved, there should be no issue. I have a Siemens 200 amp panel in my home with 20 slots. The panel is...
The bottom line is, buy the best you can afford.... You have a medium sized shop and if you buy the bare minimum now, you will realize it's limitations in short order and want to upgrade. I speak...
your best bet is to set the tools that will remain stationary in place in the 24X10 you are willing to sacrifice and leave everything else mobile. This is a very practical way to keep the garage for...
I have the Dewalt and have no complaints. Saves me the space of having a separate charger for my 18v Dewalt packs out on the counter in the shop. It will also run a LONG time on a fully charged 18v...
“Time is passing. Yet, for the United States of America, there will be no forgetting September the 11th. We will remember every rescuer who died in honor. We will remember every family that lives in...
I finished installing the DC venting thru the roof today. I am very happy with how it turned out. The noise outside is not bad at all, standing next to the neighbors house there is only a low hum.
Speaking of vinyl, you could go with VCT.
The wye is the one that came on the blower from JDS, as is configured now with the separator, I am not using it.
I have thought about the mess on the roof and it is a disadvantage of going...
As far as J-top or rain cap, that was my question, I just wasn't sure what they were called. The range hood vent type is a J-top and the chimney type has a rain cap. As for the HVAC flex, this was...
I am finally back to getting the shop re-arranged. I have a JDS 1.5HP DC I am running through a Thein Separator and going to vent out the roof of my shop. Though easier to go through the wall, I...
I have had this saw for over a year using the stock set up. If you spend a little time and do some adjusting it will work just fine. Sure I would like an upgraded fence with one piece rails, but...
Here's a shot of my shed. It is your option #1 with it extended down past the top of the wall. I don't recall how far down, but I ended up with 8-10 inches of overhang. I designed the structure...