Hi,
I have just now heard of the possibility of converting my Jet 22-44 to hook and loop. The clip system gives me fits. Can someone please steer me to a conversion kit that will work for me? ...
Type: Posts; User: Jonathan Spool; Keyword(s):
Hi,
I have just now heard of the possibility of converting my Jet 22-44 to hook and loop. The clip system gives me fits. Can someone please steer me to a conversion kit that will work for me? ...
Once your router is properly enclosed in a dust extraction box, speed changes on the router itself become cumbersome, at least for this old guy. I agree that most router speed controls leave a lot...
I’m looking at putting together a second router table. My first table was put together using a Milwaukee motor that came with a switch and variable speed control. Its been a great unit but I can’t...
Thanks guys. I have been looking at a glue joint but its kind of shallow. The wedge T&G could be the ticket. I have an inquiry in to Freeborn as to whether they have any larger sizes of that...
Here is a basic drawing of a 23' x 6' conference table I am working on. I posted in another area asking for suggestions regarding the interlocking edges.
FYI this table is designed in 5 sections,...
I am making a large conference table where the top 1.125" thick and is split longwise and across, yielding 4 sections.
The table is designed to come apart and the sections used against the...
That's excellent. Thanks
The layout demonstration is excellent. Any suggestions how to cut the facets on a tablesaw?
Hi,
It's been a while since I've posted here.
i recently made this Santoku blade with an octagonal wa handle. The bolster and butt are tenoned into the mid section of the handle.
I belt sanded the...
Thanks guys,
One more question if I may. The head is 2" thick. Blades should not extend beyond the top or bottom of the head, right?
309278 309279
I picked up this four knife head. It is a Jones and Orth that takes corrugated knives.
are these good heads? Is it up to date safety wise? Are knife corrugations standard?
thanks...
Thanks GlennGlenn
I searched, but couldn't find a solution to this.
on one leg of my DC I will have a panel saw and chop saw (as well as some larger tools). Both utilize small hose connections and hooking up a 4"...
Well, after some more reading, I am considering moving up to an 8" trunk and 6" drops to the machines. Therefore will also move up to 6" gates. I don't have time to make my own auto gates so will...
Most likely due to the weak status of the Canadian currency
Well, I haven't been here for a long time and have been away from my woodworking for a while. Life happens sometimes.
Anyway, I'm finally finishing up my shop and am about to pull the trigger on my...
Thanks so much for the advise
So, using a false front, does the undermount slide mount on the bottom of the drawer box front and the drawer back, as shown in the drawing by Glenn, or onto the inset drawer bottom with a notch cut...
I am working on plans for a mission bed withstorage drawers. I want the sides to be face framed with inset drawers.
I realized that I can't sketchup the plan until I fully comprehend how my draw...
I did the same as Mike H for my basement floor (epoxy over properly prepped concrete). Great stuff. Wish I had used it for my shop as it is tougher than nails.
I went with the pro company to put...
I like the covered floor trench idea. In one of my earlier shops I installed floor outlets, but consistantly had sawdust issues with them. If the outlets were permanently dedicated to a specific...
Greg,
Check out the video. Around the 4 minute mark.
http://www.youtube.com/watch?v=LPGG9wCMLoc&feature=related
Although I can get a clean exit hole most of the time, I still use a backer as...
+1 for Colt bits. Best I have ever used.
Well said James!
Wow, did they come gift wrapped?