Just discovered your question, Jon. Yes to your questions and the HDF (as well as the MDF) came from Paxton lumber in Denver. Not cheap and likely overkill with the laminate. The laminate was an...
Type: Posts; User: marty fretheim; Keyword(s):
Just discovered your question, Jon. Yes to your questions and the HDF (as well as the MDF) came from Paxton lumber in Denver. Not cheap and likely overkill with the laminate. The laminate was an...
I ain't a lawyer but we all know what a router is designed for and its not that. No judgement here Mark, I have done similar things, many times. The only way my conscience would allow me to get a...
410969
This was much cheaper than the Barth table. Not finished here but I ended up with MFT holes on half the table. Torsion box with MDF and 3/4 HDF on top. Laminate on top of that. Glue doesn't...
I agree. Don't get much safer than that.
410591
I agree with all above, and well worth the pittance to be a contributor. Thanks Moderators!
Marty
Which Festool site are you looking at ? Go to the page of the Domino you want, and on the right it should give you the option of including a vac for 10% off. That screen shot from amazon was exactly...
Here's Mine. I just happened to have the milwaukee drill from a job and never used it again, so i repurposed it. Just gotta be sure to loosen the table clamp before adjusting or bad things happen.
...
Have you looked at the Sawstop router add on? Seems like an obvious choice if you have a Sawstop already. I bought their stand alone router table and really like it. I put the Jessem motor in it.
...
You nailed it again Bill. Did you use that new mortiser? Beautiful piece!
Marty
I agree with the Domino XL connectors. 6 months later and still solid as can be on my king size bed.
Marty
404628
The SC is 2.8. Didn't want to replace the hood for the 3.2.
Marty
Where did this magic 25k number come from anyway? Not trying to be a wise ass but I have never seen any documented, recommended blade tensions from the manufacturers. Not doubting that number, just...
I'd rig around the spine to lift it. On mine, there is a big yellow sticker that indicates it should not be lifted by the eye bolt on top. The manual says the same thing. The eye bolt is for securing...
What kind of chemicals are you using in your shop? If you're that concerned about a little dust getting past some facial hair then you must be concerned enough to wear that mask all day, everyday in...
Please explain "power bar"! Surely you don't mean those power strips you buy at Walmart? If that is your overload protection in a wood shop with high amperage tools...well, God Bless you! Now if you...
Just finishing mine up.
398993
398994
398995
It's a Vestil 1000lb with air assist. Torsion box top with formica.
Bob Lang taught me how to build furniture, he just doesn't know it :). I have "shop drawings for craftsman furniture" and some others. I also purchased a few of his plans. I'm gonna look into the...
I had to look up Thomas Moser. I like the "fusion" of the two styles. I wish I could build a chair and sell it for $4,000.
Marty
Thanks for the compliments. I never realized how many people are into the craftsman style like myself.
The hardware came from Horton Brasses. I went with the H hinges but now I think butt hinges...
I agree with this, but I also suggest you join the Felder and Minimax Yahoo sites. I'd rather learn from thousands of positive and productive things than A few negative things. Very seldom do people...
Thanks Bill, I read that shortly after posting above.
Marty
How does all this come into play on non-crowned wheels? If I understand the theory as Van states it, the center of the blade would be somewhat on opposing sides of the crown on either wheel. The...
Thanks Kevin, I'll check it out.
Marty
I read something about using CA (super) glue to pre treat before pouring the epoxy. Helps seal up and prep the work area. Not gonna work on the big cracks but I found it seals those pesky micro...
Thanks Charlie.
Marty