Whoa, thats AWESOME Alex.
The e-mailed progress pics showed me it was going to be nice.. but with the finish applied.... all I can say is WHOA.
Type: Posts; User: Greg Cole; Keyword(s):
Whoa, thats AWESOME Alex.
The e-mailed progress pics showed me it was going to be nice.. but with the finish applied.... all I can say is WHOA.
Or if ya don't have the time to do it right, do you have the time to do it twice? :D
I made my bench with a premade hard maple top I bought from McMaster Carr. As Alex said, I added a skirt around all sides as well. It took a little work to flatten it, but other than that it's been...
Nice to see you around again Per. Lookin' at those bar pics never gets old. ;)
Welp, me thinks Joe's got it right here. D'oh. :mad:
Seems as once a month since March I've had one large unplanned expense a month... I was hoping to get through June without.:rolleyes:
There's no frost anywhere. Plenty of CFM's in the registers... so the a coil isn't plugged. The filter is brandy new as well. Anyway... my thought on the intermittent cooling was MAYBE the contactor...
The unit doesn't stop, it just seems to stop putting out cold air after a few hours of running. :confused: The condenser and fan still run and will stay running for hours. If I shut the AC off for an...
The compressor starts and stays on when the unit cycles.
I work with alot of industrial machinery and can read prints, check the cap's etc. Kinda scratching my noodle here about it....:confused:
I...
Absolutely, spray foam for insulation. Heck of an R value (depending on what foam and how thick). Ask Mike Holmes about it, or if ya have seen Holmes on Homes..... ;)
If you want to ship lap your...
So.... I'll try to keep it short. :rolleyes:
Here's the problem..... during peak times, the AC unit seems to only be pumping room temp air through the house. When it's 88 outside at 1pm, it's 88...
Looks good Alex.
I have a small assembly table directly behind my bench that I put all the hand tools on when working on the bench.
Looks like the clamp collection has grown quite a bit too. ;)
Bandsaws need to be set up properly to get good results, not saying yours isn't. Buy one of the Bandsaw books from Duginski, read it & then take it to the shop with you if you haven't already.
Also...
Buy both, set one up with the standard 45* angle and set up the other with the 50*.:D Kinda serious actually, buy one LN and then see if you can't get a rust bucket and revive it.
The only real...
+1 on the sanding before assembling.
Prefinish panels as well to avoid "naked" areas during seasonal movements of the panel.
Hey stranger, niiiiiice job.
I know I won't be showing these to my wifey anytime soon, she'll tell me to put the bows n arrows away and blow the dust off my tools & shop!:eek:
I haven't been...
Very well done, I like it.
Dan,
The scales slide in and out quite handily. I'd just remove the unused ones and the "main" steel scale is held in place by a magnet to you can move-adjust it in seconds.
I love my incra stuff.
Foamboard insulation on any old flat spot.
Make an outfeed table to match the height of your TS & when you use it to crosscut ply, just toss the foamboard on the top and cut away (just be midful of...
Save yourself the hassle & just take over the garage & park the cars outside. :D I used to try to juggle everything around in mine to be able to fit at least one car in there... that got old & a...
Hey Alex, you forgot to title the pics "PITA".:D
Another dod lover here. Best wishes to Flabby.
Our dog (puggle- 1/2 pug & 1/2 beagle mix) was hit by a car at just 6 months old. Roughly $2K later, little Rudy was in a cast and healing. The 2...
Very nice Mike.
Excellent job on the veneer as always.;)
Very nice, love the material.
I am sure your sister will treasure this.
+1 to the comment about spending a little time remodeling the home you just purchased (unless it's new). You will pick up some hands on & some tools and turn the house into your home. Diving right...
Matt,
What's the FF material? Maple as well?