Afternoon folks
We’ll finally getting settled in my new state of maine. Will be setting up my shop again and looking for a used lathe.
Have always admired conover, general 260, or other full size...
Type: Posts; User: Eric John; Keyword(s):
Afternoon folks
We’ll finally getting settled in my new state of maine. Will be setting up my shop again and looking for a used lathe.
Have always admired conover, general 260, or other full size...
Morning!
Anyone have suggestions for hardwood suppliers in Rockland maine area?
Regards Eric
HEy folks, good afternoon!
so im moving in two weeks and have broken down the shop.
looking at the jointer im a little concerned.
its on a dolly with wheels.
so i can roll it up the truck ramp,...
Morning !
I am moving soon and was just wondering. i have a Laguna suv14.
i was told originally when i bought it to transport it on its spine laying down.
initiaally the motor had to be mounted...
Afternoon!
im thinking about attempting a federal sideboard. lately ive been using sapele.
but i think the ribbon stripes inherent to the wood will be a problem.
I understand or at least think...
morning folks!
well may not be very exciting but........
hung the doors and drawer fronts on the kitchen. I know some may find it boring.
but i took the opportunity to learn about spraying a bit....
Gmorinng everyone
so if youve been followinng along. started putting primer on the doors.
it might be my ocd but i dont think so yet.
noticed here and there that after the first coat of primer...
afternoon !
enjoying my day off, sanding all the cabinet doors ive been making recently.
so my question is......
doors are poplar frames nad pine beadboard panels.
plan to spray two coats of sw...
Lol,
I guess I really need some sleep,
Just realized EUTE is the acronym.
Thank you all for your help.
i did check the can, it is the emerald urethane trim enamel.
a 1.5 tip? ok, i will order one and give it a try.
I have never seen EUTE, i will try to locate it also....
Good morning,
So im learning so please dont laugh too much
im spraying with a fuji 4, 1.8 tip
sherwin williams emerald acrylic enamel
i think i figured out a balance between spraying too dry...
Thanks Jim,
it was just a thought, but i imagine being more fastidious about keeping the gun clean
really is the better solution.
I have no idea how this project is going to go as it will be a...
im new to spraying and was wondering.......
ill be spraying pro bond primer and then emerald urethane.
fuji 4 system.
in between coats...... would it be feasible or advisable to
keep and extra...
afternoon!
i purchased to half masks to see which one might be more comfortable. the 6502 and 7502.
the 7502 is supposed to be more softer and more comfortable, honestly i dont feel much of a...
be spraying sw emerald urethane this time around.
bought the 1.8 fuji tip,( thatas what i heard works best)
thte boooth will be setup inside my garage (2 car)
i was thinking two box fans with...
morning!
So as i'm gearing up for spraying these cabinet doors,( forgive my newbie questions)
i'm planning to make a small collapsible spray booth in garage.
probably 8' x 8'. some kind of...
well, pulled the trigger.
Hope the llearning curve wont be to steep.
bought the fuji 4 with all the trimmings :)
If i do decide to go with the mini mite 4,
anyone have thoughts on which gun ti go with?
they seem to have two versions .
the t75 g is gravity fed and have been leaning to that one.
other than...
Gmorning folks,
So i'm looking into sprayers. the first project is a kitchen cabinet door replacements.
as far as i can tell, im going to be using SW emerald alkyd urethane.
but after this...
Thank you for the suggestions,
I called american filter, seemed like nice people.
ordered a new tapered bag , we'll see how it goes.
Thanks again, Eric
morning everyone,
i have an old powermatic 73 and it still is running fine for me,
i replaced the filter bag some years ago which a at the time great improvement,
i think its time to start looking...
g'morning,
well since everyone has 2 cents.
when i was younger, in the roofing business, a grey haired guy
told me "redwing" and that was all i have worn since, its worth the extra money for...
morning,
so i was looking at buying replacement doors, but what i fond online so far is pretty expensive (30$ sq foot)
the ones i have on the cabinets are white.
big box stor sells what looks...
Thanks everyone,
and thank you Bill, sent you a pm
gmorning
i'm wanting to make a new coffee table and would like to make a serpentine top.
i dont have cad drawing. im a bit perplexed as to how to make a full size drawing,
how to get the curve...