This unit is also used ny ormenental turners to sharpen the solid carbide. cutlers
Type: Posts; User: Dan Henry; Keyword(s):
This unit is also used ny ormenental turners to sharpen the solid carbide. cutlers
Do you have a source for the red white and blue corian. We Hunt County Woodturners still like to use the RWB center bands
Dan Henry
I have the inexpensive auto punch and made a hard wood knob for it and it is more comfortable to use and I think maybe more control where the punch mark will be
I made a cabinet to fit over the tolit in our mud room bath and made the cabinet to the correct size but could not get into the hole, had to made in pieces and assemble it a piece at a time ,got it...
If you have some chippy wood soak the area for threads with thin CA glue before cutting the threads and after the theards are cut soak the threads one more time, Do not change the set up and soak...
A friend of mine has a sinigle duct ac/heat pump that he ran a duct through the cieling of his garage vents it close to roof turbin and has a insulated door and cieling insulation is very conformal...
Another way to fit the pipe to the hose is to put a short section of the pipe in hot water and put a couple of hose clamps around the pipe and shrink the od of the pipe, take it out of the water and...
If you are going to make your own study and using 3 wheels think about not putting the top wheel top dead center if you use a laser light to judge wall thickness the TDC will interfere with the...
Just changed the arbor bearings on my Grizzley cabinet saw and there is a nut on the end of the shaft, with the nut off and the pulley set screws loose I was able to tap the shaft out with a fowl and...
My work bench top is 2 layers of 3/4 partial board topped with 1/4 MDF held in place with 5/8. Brads, when it is time to replace simply remove the old MDF and cut new one rough size, nail in place...
The 1/2 would not run 2 Steel CBN wheels, I now have the 1 hp and it spins up the CBN wheels very well. The rock stones that that come with the 1/2 work ok
I use the blue tap a con concert screws long enough to go into the wood about a inch and use as many screws as there is holes in the face plate. If you look at the screws there is smaller theard...
I replaced my air PVC with
Rapid Air about. Year ago and it vert easy to install so far leak free. The removing the air line from the fitting is very easy to do.. Bought the kit form Northern tool,...
This looks like the plan that was in an early shop Notes Mag.. I made it several years ago and it works fine. a friend gave me 3/4 PH motor and it is not quite big enough. I used 3/4 MDF and it is...
Looking good. Where you put screws and nuts should consider using some nylock nuts so the nuts do not viberate loose.
Dan
I ran 8 3 wire and used a 40 amp breaker and has worked great. Look at the RV breaker box you can get a feel on witch units are on each line. every other breaker are on the same line, addup the amps...
I have the 1 HPgrinder and it srartes the heavy steel CBN wheels quite fast. I had the saame wheels onthe 1/2 HP and it did not start them well at all. It did take alitle work to get the woverine...
On my shop cabinets I use 5/16 lag bolts head down on the floor, 1/2 open wench on the head makes leveling very easy and quick, most on my cabenit base have a 2X 4 in the bottom so it makes a good...
check the nut on the fan, mine came loose and I thought the worst but retourqed the nut with some lock tight and back in buseness
Dan
I had a same problem when a made a cabinet stand for my 1221 and had the lathe too close to the edge of the top, I move the lathe back an inch and now my hip hits the edge of the top rather than the...
Arlin
On the Hunt county Woodturners web site we have plans to make a sit down lathe stand that will accommodate Mini Jet lath. A little beefing up and it would handle a Delta. The lathe bed pivots...
How about building a level wooden floor on top of the slab. build the side wall on top of the level floor. Bring the siding over the edge of the floor to follow the lay of the surface. It is good to...
Got my 1221 last week and is a great t Lathe!!. I checked the spindle run out and the dial ind just wiggled a very small amount. The soft start will take some time to get used to, plenty of power and...
I have 2 fiends that have the 1221 and are very happy. I bought one at the Dallas Woodworking show last WE, on order should be here next week, can't wait. Jet did discount the lathe 15% at the show....
I have made 2 MDF lathes, 1 for my own use and one for a turning club. I used my for about 3 years and learned a lot about the world of ornamental turning that the learning curve is very steep. I...