Around here Home Depot carries two adhesive roller covers, 1/4" or 1/8". They are $5 each and you would probably need to discard at the end of the day.
Type: Posts; User: john bateman; Keyword(s):
Around here Home Depot carries two adhesive roller covers, 1/4" or 1/8". They are $5 each and you would probably need to discard at the end of the day.
The oscillating multi tools are only about $20 at Harborfreight. Worth it even if you never use it again.
I own a Rigid saw that looks similar to yours. Although I've never had as severe a problem, if I don't engage the bevel lock the arbor assy tends to rock a bit when cutting with the blade at 90...
There is a device called JOINTABILITY. It's not big enough for your project, but if you read up on it, you will see how to use a router and straightedge to joint two boards at once so that they mate...
I have seen mortise gauges which can do that, but there are no scissors involved.
Even if you get it aligned well at 0 degrees bevel, you may find it is incorrect when the blade is tilted.
The dust collector with small diameter hose will not have the suction equal to a shop vac. But it will certainly draw in saw dust.
You could probably get a hose and adapters for $20 and see if it's...
My Ryobi planer has a removable dust chute. When installing it has to engage a pin to prevent the rollers from locking up. It can easily be assembled incorrectly if you are not paying attention or...
You may find that a bearing guide bit will not go deeply enough into the recess to allow you to trim the veneer. There is a bit that looks like this that may work:
412157
Actually a better way may...
Harborfreight has a couple aluminum cases you can trim the inside foam to fit. May not be large enough though.
If you set the router on a piece of mdf with a hole cut in it and supported on a 5gal bucket, the bit will spin out when you turn it on. If it doesn't, ease the bit into the mdf while it's running....
Ordinarily I cut the veneer larger than the substrate, then trim afterward.
If you absolutely can't do that, shooting a couple 23 gauge pins thru the veneer should hold it. If you have a 23g pinner
I bought a 5ft length of 3/4" black pipe and hung it from a ceiling joist with some eye bolts. It holds about 40 F-clamps and cost hardly anything.
Is there some reason a doweling jig won't work?
I pictured the wrong guide collars for use with thin hardboard.
They would need to be shallow like these:
I think I would make the oval tray first. Then hot glue a rough cut oval, slightly smaller, of tempered hardboard to your tray.
Next use a bearing guided rabbet cutter to trim the hardboard to match...
Cut the bottom off oak blocks, drill the holes completely through the top section, then glue the bottom back on. All the holes will be the same depth.
When I had a problem like that on my TS3650, I found that cutting a piece of mdf, which is very flat and grainless, allowed me to see more clearly what was happening.
In my case it was the Ridge...
I don't know, but when I bought some to use with the brown pegboard from Home Depot, they wouldn't fit. The pegboard apparently had 6mm holes, instead of 1/4", and I had to ream out.every hole that I...
It seems to me you could just tweak the hold downs until you get your perfect miters, then glue a shim to the end of the leg that is short, so that it always contacts the fence equidistant.
No one has mentioned it, but maybe the joinery was just not good enough. If you are trying to fill gaps with glue, then you really won't get a good enough bond for something that will get wet.
In...
If you have some extra lumber and your capable of ripping thin pieces, you could just saw a 1/8" or thinner piece the same width as your leg, then glue it right over the side with the flaw.
My wife frequently spills liquids around her cutting boards, so I glue on rubberized cork discs as feet. You can find them on ebay approx. 1/4" thick and 1" diameter.
Even though her boards won't...
I made one once and had a similar problem, though I stopped before the final glue up in order to determine what was wrong.
It turned out that my planer was leaving a slight crown of about .01" down...
I can't help with the dimensions, but you might want to read this thread to prepare for the sticker shock
...