:)Second Bandsaw Tire Replacement - Grizzly G0507 20Β” bandsaw
Well itΒ’s happened again, this time itΒ’s the lower wheel tire. The other day I threw the switch and I heard this awful thrashing...
Type: Posts; User: Boyd Gathwright; Keyword(s):
:)Second Bandsaw Tire Replacement - Grizzly G0507 20Β” bandsaw
Well itΒ’s happened again, this time itΒ’s the lower wheel tire. The other day I threw the switch and I heard this awful thrashing...
Hello John, No, Peachtree talked with Grizzly, neither the rib nor the crown matters in this case. The saw is up and running and doing well.
UPDATE:
It took a while,but, I found a reasonable source for my 20 bandsaw tire. I purchased a set of two from PEACHTREE WOODWORKING SUPPLY Inc. located in Georgia. The charge was about...
Hello Jim and John,
When it rains it pours, everything happens at once. Ill start at the beginning, my neighbor came over Friday at noon and I went through all that we have experienced here...
Hello John,
I can't talk right now but I'll get back later this evening or as soon I can with pic. :)
Boyd
Hello Jim,
The BIG day is tomorrow, I talked one of my neighbors into giving me a hand in attempting to mount the tire on the steel wheel. We'll find out just how good the rubber is and or how...
Hello Jim,
After reading your last post, I immediately went down to the shop to perform a very light pull-test on the bandsaw tire. With a very light tug the butt joint came apart. So, I used...
Hello Jim,
Its been approximately ten hours now since I completed the glue-up (see pics).Just took the tire outside from the shop to allow the SUN to help cure it. To my surprise it appears to...
Hello Jim,
Attempted to use your fix and here are the results ( see pics). Got the tire tight on the wheel and inserted the two broken pieces and to my surprise there was still a considerable...
Thank you Jim. I think I'll try this. How did you hold the tire to the wheel until it cured?
Boyd
Hello Tom,
Having a running gun battle with the manufactures (Grizzly) days are over. It was my intent to make other woodworkers aware of not only what I have experienced but to have an...
Hello Everyone,
Its been sometime since I posted last, although, I have stopped in every once in a while to read some of the posts. I had an interesting experience with my Grizzly G 0507 20...
Hi, This thread may help you.
http://www.sawmillcreek.org/showthread.php?t=7761
.... Wish you well on your venture.:)
.... There is a good chance that you might be able to get this at Wal-Mart in the RV section at a better price! Your best price is most likely going to be a contractors electrical outlet store and...
Hi Burt,
.... In this case, I can't help but to agree with you especially in "OFF TOPIC DISCUSSION". You impress me as a very flexible and open-minded sort. There comes a point when there is too...
.... Me too.
Thanks Burt
.... What BackUp PROGRAMS are you using for your Sata Drs?
.... If there is a Video card installed in it, and not incorporated into the mother board, take it out and reinsert it. You may need to do this a couple of times to make good connections by shining...
Tim,
.... When you installed you're WIN 7 did you start from scratch (Format the partition or Hardrive and install) or did you do an UpGrade?
....So where's the pics? We're still waiting :p?
.... May I offer a suggestion that at a minimum type in an inactive address so we could at least copy and past in to our browsers. This would, I would think, make it a lot easier on me and other...
.... Very much interested in seeing the completed picture. . . . .
...."CEMENT" that's pretty good. When the computer is always waiting for me and not the other way around then we will have arrived.
Hello Dean,
.... What we have found that works best is (S&D) 2729 6" pipe. It's manageable and reasonable to cut. Here are two Ref. to earlier posts that you may find helpful including making your...
.... Welcome to the real update world, sorry to say :p.
.