#2 MT available for $95
Type: Posts; User: Joe Kaufman; Keyword(s):
#2 MT available for $95
A friend receintly received a couple of Nova jaw sets that looked like they had been deburred with a coarse wire wheel. The scratched and abraded edges were noticeable from 6 feet away.
Aligining the blade to the tilt axis is not a simple procedure. The notice on page 67 that states "This alignment procedure is not intuitive" is correct. There are probably no shims under the table...
Mine has 2 setscrews to adjust the swing away parallel with the bed ways. It could be that the swing away is slightly high or low towards the end of travel of the tailstock. I had difficulty with...
Any code displayed on variable speed drive controller when it won't restart?
Position the headstock and tailstock toward the center of the bed and lift and move with a motorcycle jack under the center of the bed. Not something I would want to do daily.
About 6 months ago a 3520B with extension went for $1450. I don't believe it was ever listed on craigslist. The previous owner was a woodworking club member that had passed away.
The bearings in mine are NIS 608Z. There is a brass bushing that extends through the I.D. of both bearings and they are mounted on a 1/4-28 socket head cap screw.
I have the instruction sheet and parameter manual for the Delta VFD-S inverter used on the 3520B lathes. I do not know what inverter is used on the C model as it is covered. I quickly reviewed the...
I turn 90% bowls and purchased the curved Robust Rests about 4 years ago. I have used the inside curved a couple of times and don't remember using the outside curved rest. They sounded like a great...
The manual clearly states 230V. single phase input. The local Rockler store manager mentioned last month that he had lost a few sales to schools and business that had 208V 3 phase distribution. He...
You are correct, one end is taped 3/8-16. I didn't look at that end because of the installed tailstock swing away. The pattern on both legs is tapped holes and there are bosses cast in the legs so...
That's good to know. Maybe the thickness change was between the 3520 and the 3520A. I do have the
6294727B bed extension, still in the original box, unused and sits on the shelf between the legs...
My B "way" thickness is 0.558 inch. Was under the impression that the B was thicker than the A. What is the thickness of your A model?
The Nova sure appears to be #2MT. The machining on my Nova points are rough but they will hold in the lathe spindle taper.
Update...….
I forgot I had the Nova with small removable tip. The...
I would approach the bearing change by purchasing a 3/8-24 X 6 inch hardened Socket Head Cap Screw, make a washer that just fits through the inside of the female taper and a sleeve to pull against...
I would guess that the air is leaking past the piston and cylinder limiting the pressure output and indicating a damaged ring or cylinder surface. Does the air continue to escape the oil filler plug...
The Husky shows $149 at 5 nearby stores subject to stock on hand and all show at least 1 on hand, Anaheim-Fullerton CA. Was considering this compressor for $169 last month but settled for a CAT...
Mark, your link goes to a S400-1002 which is a momentary type.
In addition to the problems listed above, is this what you really want?
It will only be on as long as pressure is applied to the foot switch.
From the wiring diagram - "Action:
momentary...
The drill press would be considered a consumer product and therefore should have a UL listing. Harbor Freights 8" drill presses have the UL listing. Twenty years ago Underwriters Lab did not...
Charley,
The point is, if the motor is a permanent split capacitor design, there is no centrifugal switch. I have run across it before on a similar small imported drill press,
The drill press...
It could be a permanent split-capacitor motor where the starting winding is connected in series with the capacitor and parallel with the run winding. The starting winding does not drop out of the...
I've had a Stewart Batty Carbon Fiber ER25 collet handle for about a year. I really like it. There is also a ER30 collet version that will take 3/4 inch tool shafts. A little on the pricey side is...
Did not contact SawStop. The alignment process is well defined, but pretty convoluted with several warnings. I discovered shortly after attempting the process that the miter slot was tight at the...