Bob,
Try McMaster-Carr - www.mcmaster.com Click on Raw Materials, then plastic, then rods and disks - you're on your own navigating from there :). I haven't bought any plastic from them, but...
Type: Posts; User: John Durscher; Keyword(s):
Bob,
Try McMaster-Carr - www.mcmaster.com Click on Raw Materials, then plastic, then rods and disks - you're on your own navigating from there :). I haven't bought any plastic from them, but...
I heard there was an Amish or Amish like mill somewhere near Mechanicsville, you'll have to find a local to determine if this is true.
I'm in Ellicott City, so the places I go tend to be north or...
Kevin,
I have the screw type festool clamps, as opposed to the quick release version shown in your picture. Here are the dimensions for the screw type Festool clamps as compared to the dimensions...
I use a Veritas Scrub Plane from Lee Valley to do initial clean up on rough cut wood. I usually hit the board with a wire brush to do the initial cleaning and then use the scrub plane. It makes...
I have a shark guard. I really like it. It really is worth the wait.
John
I've had mine several years and am very happy with it. Just make sure it is on when you switch from low to high speed.
John
I've got a Rikon, I've had it a few years. It is okay, but the wheels on mine aren't in the same plane so the blade won't run in the middle of both wheels. There doesn't seem to be any way to...
I installed hardwood floors and refaced the stairs in my home. I would recommend Hardwood Floors Laying sanding and finishing by Don Bollinger as a good reference.
I used prefinished flooring...
Count me in please.
Thanks,
John
Please count me in.
Thanks!
John
Mike has a good point, check to make sure the feed belt isn't slipping. When I replaced my feed belt this week it worked at first and then started slipping.
John
Jeff,
I just happened to have downloaded the performax manual last week to replace the feed belt so I'd just been reviewing the troubleshooting part of the manual. I copied the following from the...
Are we there yet? :)
I'd just put drive small flat head screws straight down into the rabbet directly below where the adjusting screws on the router plate contact the rabbet. Take the adjusting screws out of the plate...
Thanks!! Please count me in.
Count me in. Thanks!
My wife regularly goes to a local craft center to make pottery. She takes the sawdust to the craft center and they use it to make Raku pottery. Evidently they take the pottery hot from the kiln and...
Count me in. Thanks!!
I put my used finishing rags in a specialized can for oily rags. I got mine at Griots garage - http://www.griotsgarage.com/product/in+your+garage/garage+clean+up/six+gallon+oil+rag+fire+safe.do ...
Jim,
I haven't ordered these yet - the glass for the cabinets just came in so I wanted to get that done (and paid for) first. The lights I am leaning towards are at...
I just completed a display cabinet for my wife's pottery. I'm going to try LED strip lighting. They have these little 4" strips that can be connected together for whatever length you want. This...
I'd plan the layout better, but the biggest thing I would do is pick a different house! The house is nice, the location is excellent. However my shop is in the basement and I do not have a walk out...
You might check to see where all your bathroom and dryer ducts exit the house. On my house the builder ended the bathroom vent's ductwork into the attic. I've since made it so that it vented out...
One of my wife's hobbies is pottery. The craft center that she goes to takes all I produce. Evidently there is a kind of pottery called Raku. What they do is fill a steel garbage can with sawdust...
I've been using McFeely's fasteners for a while now and have been very happy with them. I really like the square head screws since they don't seem to cam out as often as the phillips or slot screws....