Well the best way is to use Hoffman dovetail key. The machine is not cheap, but if you make a lot of picture frames, it is worth it.
https://www.youtube.com/watch?v=LX-qyEJO6Fk&t=2s
...
Type: Posts; User: James Zhu; Keyword(s):
Well the best way is to use Hoffman dovetail key. The machine is not cheap, but if you make a lot of picture frames, it is worth it.
https://www.youtube.com/watch?v=LX-qyEJO6Fk&t=2s
...
ETS EC 150 is definitely better than the old ETS 150.
It has low profile design, brushless motor, carbide pad braking, active electronic vibration control and jetstream dust extraction.
Aigner Contermax is probably the best coping jig except for those sleds with clamping cylinder, very easy and fast to change the stock. It just takes way too much time to change the stock on...
Jim, if you have space, this crazy horse dolly (https://www.thecrazyhorsedolly.com/videos.html) makes handling sheet goods easier.
Steve Rowe's youtube channel (https://www.youtube.com/channel/UCmE9bhjfyhepnFlyXFkWwsQ/videos) has a few videos about the sliding table saw. Saw Stop's added on sliding table is far away from the...
I wish Mac's airtight clamp is supplied with the slider :)
http://macsblogboard.blogspot.com/p/airtight-clamps-gallery.html
The sliding table should be a little higher (0.004" to 0.008" is ok) than the cast iron table. If you do not have Fritz and Franz jig, make one (https://www.youtube.com/watch?v=Q0PyFjtSHrE&t=463s).
...
Lamello Cantex is definitely the best edge lipping planer, and fool-proof. But very expensive.
For a hobbyist, the edge trim kit from P Power Tools plus the dish carving bit should work.
...
It is very easy to get 3 phase power from single phase. You can use either a rotary phase converter or digital phase converter (Phase Perfect).
Yes, it can be done using Shaper Origin, the world's first handheld CNC router.
https://www.youtube.com/channel/UCLy2jg5-SD84OCbiiDoOAJA/videos
Dimar multi profile cutter with limiters is nice, the 40mm profile knife is cheaper than Felder's, and Dimar has all the profiles Felder has and more. And I think for the same profile, Dimar and...
27 mm hose should be fine for DF500. I have CT26 with dust deputy and 27 mm hose for DF 700.
Mini is too small. I have MIDI for portable use, yes, need to buy expensive filter bag.
If you do...
In cold climate, the shop needs to be heated in the winter season. Not only for the comfort, but also keep the tools from rusting.
James
For a shop that size (40' x 50'), separate is the best choice. Here below would be my preference for Euro machines
1. All separate
2. J/P combo, saw, shaper
3. J/P combo, saw/shaper combo
4....
Pull the rip fence to clear the blade, use the "Fritz and Franz" jig, you will get consistent ripping width using the slider, it is safer and faster. This technique is clearly demonstrated in the...
You do not need to see the blade to line up the cut. I add a wooden block (zero clearance to left side the blade) to the end of the crosscut fence. I also use Fritz & Franz on the slider, I can see...
There is a simpler and better way to square the crosscut fence without using 5 sided cut method, check this David Best's flicker forum post...
I believe on Euro slider, both rip fence and sliding table are set to be toe out to the blade, this is for preventing the kick back.
A oneway multi-gauge or similar tool is needed to set/check the...
I have KF700sp in the two car garage, and I keep the router table. Felder router spindle is not cheap, about $1000, and rpm is still low compared to router.
Besides, the changeover between saw and...
It would be a problem to rip such long narrow piece using the sled on the cabinet saw. Piece of cake doing this type of ripping on the sliding table saw :)
Use a table saw sled, place the sled fence stop 1/4" from the blade, put the 1/2" board on the sled until it touches the stop, then move away the stop and cut.
It would be better if you could make...
I adopted the method David Best described in the following post, simple and effective, it works perfectly when using rip fence as a stop on the slider.
...
Thanks Andy.
I find Kanefusa fine crosscut blade and glue joint rip blade on their website, not combination blade though.
https://shop.akhurst.com/canada/kan27-11-8x072txd-01-g.html...
Where do you buy the Kanefusa blade in Canada?
That is the Aigner deflector. https://www.werkzeuge-fuchs.de/en/mi...ort-workpieces
You can download Aigner catalogue to see the detailed description of the deflector, it should be easy to DIY...