I'll be traveling through Syracuse NY this week and am at a loss of where to go and get some lumber. I have a ton of cherry as I'm from PA but am searching for some 5/4 - 8/4 QSWO or some nice black...
Type: Posts; User: Brian Parker; Keyword(s):
I'll be traveling through Syracuse NY this week and am at a loss of where to go and get some lumber. I have a ton of cherry as I'm from PA but am searching for some 5/4 - 8/4 QSWO or some nice black...
Good question, unfortunately I didn't think of that when I snapped the picture. The picture frame shown on the bottom has an opening 5.5" wide, each side of the frame is 1 3/8" wide.
I got the Jet 426238 3/8-Inch X 50 Air Hose Reel (rubber hose) mounted up to the ceiling. It took a little while to find one that wasn't $300 but the bay paid off and I haven't looked back. Highly...
I would like to know for two reasons, the first is I'd like to buy more of this if I can, but I also want to read up on finishing techniques / colors for it.
A while back I purchased some small...
I'm going to be staining a project that I've been working on once the weather warms up a little as I'll need to leave the garage door open a bit to get the smell out by circulating air with a fan. ...
I got a decent price on some Cherry and began gluing it up to make a TV stand only to find that the wood is not cooperating. Pieces were flat when I glued them up only to find that they have...
Thanks Bob,
I called my local Ace and they said it was in stock but they couldn't find it when I went. I tried a local ma and pa True Value this past weekend and was rewarded. They didn't have...
I'm finishing up some curly maple frames (finished with some transtint mixed with distilled water) and I was going to use Deft Satin or Semi Gloss Spray only to find that Lowes no longer carries Deft...
Kevin, you are correct in that the 3" is an add on item. I've read where some people purchase it saying that it's a must have. Perhaps this is due to lack of ownership but after a 2" spindle why...
I've been looking for an oscillating spindle sander for some time and believe that I've narrowed it down to the Ridgid edge/spindle and the Jet JBOS-5.
I've looked at the Grizzly's but the...
Thanks for the mention of Hearne, is there any other place(s) that one would recommend?
I'm going to be working on a corner TV stand and I'd like a nice thick top (and bottom) for it. I've been calling around my local suppliers and can't find a nice supply of 6/4 as most places seem to...
I'm getting ready to make a corner tv stand and plan on incorporating a couple of drawers into the unit. The dilemma is what to make the drawer boxes out of as the main piece is going to be a nice...
I never heard of this ATF (or power steering fluid) and acetone combo before. After a quick google search this looks like something that I'll have to whip up and keep on the shelf. Thanks!
Thanks for all of the responses. After about 45 minutes in the garage I was able to get it torn apart and cleaned up. I pulled all the set screws, knobs and bolts that I were around and sprayed it...
I thought of that but dismissed it, then thought of it again and then thought to come here before pulling out the mini sledge. I thought using a hammer and beating on the rear of the tube may work...
Thanks for the ideas, I got it resolved this evening!
I've had this jointer for about 6 years or so and until about a year or so ago loved it. I went to use it one day and found that the big...
Hummm.... I was hoping to get a few more perspectives on this...
Both of these are some good points. I don't see banging on steel in a wood vise regardless of what it's attached to. If anything...
I’m going to be making my second router table soon. My first I gave to my dad, it was built from the New Yankee plans which at the time was good since I didn't know what I really wanted. I have...
Mark,
Thanks for the information, I'll be sure to give the Senco's a test drive in the next few days. I was in the Blue BORG shopping and noticed that the flooring screws were indeed the famous...
I did a quick search and I didn't see anything related to this. I just got the Makita 6834 in the mail and plan on putting it through the paces just as soon as I can get some fasteners for it. I...
Ok I'll be the first to say it.... man your vac sucks! (yes it may be a bit corny but others were thinking it)
a bundle weights about 75 lbs, so 3 to a sq = 225/sq x 20.3 (buying a little more than one sq extra) = 4567lbs ~ 2.23 tons, toss in another hundred lbs for tar paper and it would fall in line closely.
Chris,
The airless seems to be the best choice, check out Gleem Paints. If you don't mind a recond there are alot of great deals at Gleem. If I was to repaint a few rooms in a house I would...
Here is an article about it from our friends to the north...
It appears that there are a few recommended methods
enjoy
http://www.casma.ca/cas_tech13.shtml