Search:

Jacks number is good 1 HP for every 4" of jointer. Look at any larger jointers and that is usually the case or more. The General 8" it came with a 1 1/2 HP and later changed it out to 2". ...

Ive seen some you tubes past hooked up to welders and the ones I saw didnt work.

I barely look at grain, maybe edges maybe not. directions changes in many boards, put the board through and it will tell you. Feed rate is most important I can run birdesye one pass one shot...

I wondered if there is a category in the book for most lies. Turns out there is a category but legal profession and politicians are barred. Guess there would be no room left.

Would makes...

feed rate is huge, being able to control it over and above many planers is the difference between blow out and clean cut. When I have time ill be putting a gear motor on the SCM and maybe the wadkin...

taught hollow ground by cabinetmakers. One aspect right off the bat is there are two points to rest the bevel on when honing, makes it easy and maintains the same angle.

if you judge an Excalibur then consider there were likely five generations. I had two on one saw, they were first generation and primitive but on smaller stuff worked great to square one side then...

went out after 4:00 am Sat (friday night) sky was full of pulsating patterns. No extreme colour and not super bright but tons of it. Video taped and not looked yet and dont think it will show...

got done today. boiled water several kettles woth into a cooler. Different automotive details brushes and only one or two of 10 was strong enough. I took water in a squirt bottle and good I did...

few photos, two from the canadian site. Be nice if the you tube showed the saw working rather than just running. Makes sense if you are wanting to sell something.


519608519609519610

I don't get blow out as I climb cut but its hand held so you have control, your thing doesnt lend itself to that sure you are using a router table. Shaper high speed steel or insert head has an...

its being played through the same TV and the same Receiver,non of that changes

Either the computer DVD and audio portion in it is equal to and as good as a separate Sony DVD player or its not,...

I don't care about recording its only playback

what I want to know is now I run a Sony DVD for the picture into a computer or direct to a TV ill have to check that.

The sound portion goes out...

I have computers in the shop rooms to have you tube or DVDs. Ive asked two computer guys twice is the DVD player any better than the DVD's in computers and no response.

The main machine room...

Thanks Larry, here is how I run the lap top when I had it out, all fits into an old samsonite briefcase. I cant stand the mouse on a lap top so have a logitech anywhere three, it has forward and...

You can choke down on stuff I used to use vice grips on the hose to not full close, you have adjustments and can make a very fine spray like a tig welder compared to arc.

Agree with Dennis I once didnt hire an arborist cause of a joke he told me. After I said your not the guy. Hired someone else and he was excellent.

Ive had struggles with one auction company...

im guilty of that. I usually dont proof read either so far from ideal. The old guy had poor english at times but good most of the time. I saw past that, he could eat anyone experience wise.
...

get a pressure blaster and you can run it low if you use Aluminum Oxide 25 lbs to 50 lbs will do work. Ive done car parts in that pressure range. I use 56 grit which is fairly fine running off a...

Rob you seem to be saying he was making telephone calls from the lap top? is that possible or am I misunderstanding that. If I could use the lap top like a cell then that would be nice. Its the...

thanks Mike I had approached them and came in and saw your post. There were originally two one each side of a door. Told neither will make it they did then towards the end of the season the ritht...

wow thats quite the adventure but you got it. After asking upside down then I though the spindle will turn. See you solved that as well, nice idea. I have the same machine. Needed bearings when I...

Up until a few years ago carried my keys this way with the Swiss knife I got in 84 in Venice. The red sides were broken off. Knife in my back pocket keys hanging out. Worked fine. I wanted to...

I get this image.

https://www.youtube.com/watch?v=6G_1_T0ec_E

can you turn the machine upside down to work on that.