Matt did you get this sorted out?
As I recall the motor voltage conversion on mine (circa 2002) was done in the motor fwd /reverse switch not under the motor cover I can look tomorrow when I go to...
Type: Posts; User: John Aperahama; Keyword(s):
Matt did you get this sorted out?
As I recall the motor voltage conversion on mine (circa 2002) was done in the motor fwd /reverse switch not under the motor cover I can look tomorrow when I go to...
Go to Penn State Ind website and down load programming instructions. mine is 16 years old been dropped and abused for that long still works like a champ
Steve I cannot say that I have ever heard of a conveyor belt like that most people stay with the sandpaper belts or do what I did and went with a poly belt (after I struggled trying to align a new...
I think that if you unbolt (4x bolts) the drum carriage complete with drum you can then work on the inboard clip. The little screw in there has a retaining nut I have not done this myself but am...
I think what you are maybe thinking of are blade stabilisers.
Were in fashion for a while I had a set found they limited depth of cut so much as to be useless forget them and rethink your intended...
A 1/8 blade is, in my experience only available as 14 tpi or 18 tpi.
I buy 1/8 Supercut bands by the dozen last me about 3 months.
You have to call them to order.
Greg it very much depends on what you put into it.
A 15 in planer will fill most bins very quickly dust from edge sander drum sander table saw much slower.
I have a portable Grizzly on wheels has...
Klingspor's Woodworking
I am guessing you did not buy from grizzly they do not supply machines with plugs.
For what it is worth all of my machines use 220v plugs as shown some are 5hp no problems.
If you are concerned...
Can try to vacuum glue in etc but unless it is going to collapse just leave it . It adds to the patina or history of what has become a family heirloom warts and all.
Poly belt is way better than the paper.
These things are so generic that almost all of the gearbox parts will work on each other Grizzly may be able to help here.
Eric been thru this very thing recently only on a 22/44 plus.
Bought a drive belt from Supergrit (i buy ALL my paper from them) for all the trying I could not get it to track major disappointment...
How accurate do you really need to be? What type drill bit? I always use forstner.
I do this a lot 3/8 in 5/8 always seems to be minor wander. To prevent jaw marking on stock dowel i split a piece...
Point of reference would be my 22/44 it runs to 250 odd lbs that is just the unit no base etc assume base could quite easily run to 200 by itself call supermax I am sure they can tell you.
Other...
Have one, got the table top at the same time. Very happy with it. Picked it up 'will call' direct from Incra.
Thinking about getting the extra magna lock plates.
Check your capacitors.
This mill drill has 2 inches of spindle travel and 11 inches of column travel more complicated than it needs to be.
Is this a precision hole? it is in wood so probably not.
There are drill presses...
Have corded version has become very much my goto tool, lots of power clean accurate cuts.
Stay with the correct belt and get them as a matched set from Powermatic .....very important
Dick Is this a DC-380? 15x6 planer the part you reference is for a 13inch portable planer (best I can make out) actual part i think is 1349383 google it seems to be available at master tool repair....
SuperCut Bandsaw Co I buy 10 at a time free shipping good quality blades
It shows as being in stock part # P1021166 $13.25 (complete assy)
Using stops on the carriage and a dado blade very effective and I think safer than a jig. Assuming that you can use a dado, many sliders cannot I have a Grizzly G0623XZ.
Supergrit for very good pricing and very fast shipping also use their split paper roll for brush heads