I have a 2017 Chevy Bolt. Purchased "new" sort of in March 2018. Previously titled with 699 miles on it when I took it home. Currently something over 18,000 miles on it. Drive 22.1 miles each way to...
Type: Posts; User: Mike Lassiter; Keyword(s):
I have a 2017 Chevy Bolt. Purchased "new" sort of in March 2018. Previously titled with 699 miles on it when I took it home. Currently something over 18,000 miles on it. Drive 22.1 miles each way to...
I don't know. If the switch is tied to ECU it could ground circuit when pedal depressed and ECU would detect that and know to deactivate cruise control. I was trying to describe a "maybe could be,...
not for sure about your specific truck, but look under the dash to the area the rod from the booster attaches to the brake petal. "USE TO BE" a couple of switches that the brake pedal would push...
Bob I have GE frontload washer and dryer stacked in wash area in hallway to our back door in a double wide mobile home. Ceiling is vaulted and units are against the rear outside wall where the...
Ed the compressor cannot maintain 30 psi with the volume of air being used. Putting your finger over it and blocking the opening lets it build up pressure due to zero flow. I would look at the filter...
something else you should consider, is what the ratio of oil to fuel is if you have other equipment that requires mixing oil additive in the fuel. You would be wise to get a blower that runs the same...
yea, you have a point. :rolleyes:
I know. BUT my old struts are still quite strong - I can barely compress them by hand and cannot the new ones at all. Rated at 150 pounds strength. I would be concerned of getting ones strong enough...
I didn't include the website because I wasn't sure it was allowed to. Figured I provided enough information without doing that for anyone to locate the right place.
FYI to anyone that may have ULS ILS series laser and need to replace the gas struts that support the top door.
Mine grew weak, and occasionally would drop the top door on my head while I had it up...
I understand about the ascenders and descenders. It messes things up often doing embroidery when you have a "y" for example. Everything here was all caps and straight lines across the top and bottom....
I sort of stumbled upon this a couple of days ago and had to sort of work around it to get the text sized as intended. My understanding is text normally sized by "points" with 72 points equaling one...
Kevin, I've got "a little" experience working on mobile homes. I doubt there is actually a vent pipe at the toilet. In the ones I have (and have worked on) be it a single wide with a metal roof or...
sort of how I view it too. "my price" doesn't depend on their budget, but I also agree with Scott that knowing what they have in mind spending allows one the provide options that could allow the...
;) and that's allowing them to get more than they thought for a little more if they want it. I agree with you. You aren't attempting to take advantage of them, and giving them a chance to upgrade I...
IMHO - you prepared the price quote knowing they were in a rush. You came up with the price you would be happy with under the circumstances involved. So afterwards you find out they where prepared to...
and the grocery stores do the same thing. Someone not knowing any better will think it's a good deal until next week when the "on sale" price tag is gone and the normal price is again posted....
around here calcium no longer used due to rusting tubeless rims. I was told they put "alcohol" in them. Like used in windshield washer fluid I think. Non corrosivfe and very low freezing temp. I have...
you have more rubber in contact with the ground with the turf tires if you are on pavment or concrete than ag tires would have. R4 tires better than R1 tread due to flat fatter lugs on hard surfaces....
+1 I saw nothing about it
use quick setting concrete in bags. It sets fast enough to stabalize the post in the hole and is easy to work with. I would not put water in the hole before pouring in the mix. It would be very easy...
thank everyone for your words. I recieved a couple of pm's as well. Thank you too.
We laid Kevin to rest this afternoon. I spoke to Kevin's son several times and I am convinced Jerry knows Kevin...
isn't the code on the jacket or plastic the disk is protected by?
Thank you
There is loss even then. There would have been many more he could have influenced just by being himself and going about his daily life. He stood tall. Hard to envision I guess that non...
I understand your remarks, but honestly to my way of looking at this - it is MY honor to be a pallbearer for him. It is the last thing I will every be able to do before he is laid to rest. A...