Inch:
0.666 Bore Spacing (~43/64)
0.4175 Bore-to-Edge distance (~27/64)
3.5 Overall Length
Type: Posts; User: Tom Esh; Keyword(s):
Inch:
0.666 Bore Spacing (~43/64)
0.4175 Bore-to-Edge distance (~27/64)
3.5 Overall Length
That's completely normal for LI packs. The circuitry monitors voltage and temp, shutting down if either is outside a predetermined range. That circuitry, as well as smarter chargers, are essential...
Definitely not. Even in a dry climate it'll gradually start turning into something like cardboard from the outside in.
I've had excellent results using shellac as a sealer, followed by poly for a...
I've used it on cherry. Slightly darker initially than BLO (and more uniform), but of course after a few months of cherry's natural darkening anyone would be hard pressed to tell the difference.
I've got two of the smaller C'Man in my router collection. Exceptional value, worklight, reasonable dust collection, and standard (for PC bushings) baseplates. However the fixed base on at least one...
I suspect you mean voltage tester but in any case relying on a $10 model can be dangerous as they act exactly the same indicating a dead circuit as when they fail or are turned off. For a little more...
1) I'd stop with the gray pad. Problem with trying to finish metal with sandpaper is it breaks down so fast. 220 becomes 400 then 600 then wears out entirely in pretty short order. Makes it hard to...
I've used the Bostik on twist drills. Really helped clear the chips & avoid overheating on some deep bores. Only caveat is it has a distinctly unpleasant STINK (like burning rubber) until it dries....
Similar experience, plus a 40 mi round trip to their SC to exchange the packs. Seems they went out of their way to locate it as far away from the population centers (and dealers) as possible in this...
I'd suggest trying a thin-kerf blade if you haven't already. It's the equivalent of adding ~25% hp.
They certainly beat running at only full speed, but I found I had to watch the feed rate carefully and maybe set a higher initial RPM to avoid bogging down. I've never investigated how the integrated...
In addition to not working with VS routers, the external controls aren't the best solution for another reason. Since the external control only reduces power to the motor (no feedback), the torque...
I didn't notice much difference with Forstners, but it sure improves chip ejection on twist / bradpoint bits. Saves a lot of time pulling the bit to clear chips when you've got a bunch of deep bores...
+1.
I've also found a vac hose positioned near the bit helps immensely. It pulls extra air across the bit and more importantly clears the cuttings. With a sharp bit and proper speed / feed,...
That's because the Resaw King is a carbide tooth blade and given the large number of teeth on a BS blade they're pricey. As you might expect, they hold their edge a lot longer than steel and can...
Yeah, the dang instructions are just plain incorrect. They need to be located about 1/2" lower on the base, or start with the lid at around 5 degrees less than noted if you want complete closure. In...
+1
After suffering several of the riduculous gurgling variety, I bought 2 of the No-Spills at my local equipment dealer. Somebody finally got it right.
I've done it many times and I've never felt it was much different than a 90 deg cut safety-wise. However I use grip-faced push blocks to feed dado cuts, not only for safety but to keep long pieces...
If the small cut radius is the primary consideration, don't worry about tpi. Higher tooth count will work fine (in fact you'll get a smoother cut) but just not as quickly. I actually prefer a high...
ADSL2+ refers to the latest implementation standard (which is good of course). Bonded means it's "stackable" in a sense - for example two physical DSL lines would work together to provide 2x the...
Check these out. Very comfortable. They don't go in the ear canal, but seat around it on the outside.
http://www.woodcraft.com/Product/2005488/16255/Zem-Hearing-Protection.aspx
I use the same vac with a Clearvue Mini separator for everything except the planer (I need to rig a bigger bucket). It'll work fine however don't expect it to last forever doing DC duty. I'm on the...
Nothing wrong with big paddles or bump switches, but if retaining control of the material requires some awkward or dangerous position, it's really time to rig some auxiliary support.
You're correct. A bunched up rag soaked with shellac or alcohol just dries & cools more slowly. OTOH when you confine an exothermic reaction like BLO curing, you increase the temperature rise, which...
+1 for Bosch. Going on 5 yrs, no issues. Does an excellent job and almost silent.