Search:

aka...Sliding Stock. Would depend on how old the plane is...those with the arms that screw into the body might be just a tad smaller and have a different, all metal design...Later ones with the...

Fetch & Carry is done...for now
8 blanks for drawer fronts
4 blanks for a panel to be glued up into the Top...saved a couple strips for the Bread Board ends..

Just got TOO HOT in the...

Today will be a "Fetch & Carry" sort of day...
Sort through the Stash of Ash..carry a couple planks to the shop..try to find a few good blanks in them to make Drawer Fronts with..then go back...

Got me to looking...
520091
hanging there, between the Jackson Backsaw, and the Disston D8 Panel saw..
520092
Handle hardware.slotted screw is just that...a #12 wood screw..
520093
There IS a...

Prototype of the fancy bottom Ash Filler strip...had a problem..
520087
Can NOT have this gap....so..remake a new, Improved one..and zero gap...

Installed with clamps, screws and glue..
520088...

And, somehow get the Case up onto the tablesaw's top..
520085
A bead of glue along one edge...screws to attach the plywood to THAT side....rotate the case, bring out a BIG 3/4" Pipe Clamp to pull...

Ok..first off..corner braces..that are used to attach the top to the case..
520080
Just diagonal strips of pine..glued and screwed in each corner...there will be an "air gap" between them and the...

Because...I needed to get this mess off the assembly table, and place Side #2 up there...

This time...glue into the sockets...run a bead down each of the 9 runners near each screw hole...LIFT Side...

Started with just a dry fit..
520013
As this frame was labeled as Bottom frame...

Got out the screws, the bottle of glue, a BIG square..and something to drive the screws with...Big Square?...

Side #2 is done..
520009
Drawer runners are done..
520010
Back rails are milled...
520011
And all are assembled with the front rails..to make 9 frames...
520012

So..next time will...

Eric Brown ( on this site) would be the one to talk to about this saw...

I do have the Bishop No.10 version...
520005
That I leave set up for Dovetails..

Been one of THEM days, today....go to type a reply on a website....circuit breaker the Computer is on ( and the House AC Unit) decided to pop...
Decided to kill the time the computer will need to...

So..was a long day...but..
519894
All 9 are done for THIS side...next?
519895
Need to transfer all the layout marks to the case's other side...and mill them..

Wanted to get this out of the...

Set the rip fence to guide the router..
519891
Have to allow for the router's base...including how far in to go..not too bad...?
519892
Got set up to do #8 socket...was running out of a place to...

Tablesaw as a work table/
519887
Works in MY shop...as long as I remember to lower the blade all the way down..

Set up a router, today..
519888
Block is the "backer block" when I milled the...

Ok..yesterday...Had to go and bring the Boss home...(LONG story) THEN go out and pay the monthly bills, and Grocery shop....Then a trip across the street to Lowes..
On Sale!....1 x 2 x 4'....Total...

Ok..got all 18 runners done..
519857
However, came time to cut the pine back rails..
519858
There was only enough GOOD 1x 2 left for 1 back rail....Trip to Lowes yesterday to restock

I had...

Set the router table aside, for now...cut 18 drawer runners on the tablesaw for length..
519848
Here is about half of them....each need a tenon on each end..
519849
Nibble away...working away...

Ok, dovetail bit was done..time to change bits..
519844
There was a time, long ago, where a router by B&D was all metal, and was a clone of a DeWalt No. 610....and both needed 2 wrenches to change...

1st Router table use...needed a jig to slide along the fence..
519835
To run parts past a dovetail bit..
519836
9 "rails", dovetail "Tails" on each end...takes 4 passes

Goal was to match this...

Will do an "Up-Date" later this evening..once we get the Boss back home and settled in...
Warning: Router Table will be in use
Warning: Tablesaw will be making tenons

Weird Sign award: This...

Thinking the term does or does not include slicks?
519786
And maybe not from the realm of Timber Framers?


Shorty is 11" long..and a mere 1-1/2" wide...
Big Brother..is 15" long, and an even...

ok, to get the rebates milled..
519750
Had to move these out of the way...cauls were a might too close to my arms as they were going by..
519751
Used the Craftsman3720 to mill a 3/8" wide by 1/4"...

Curved areas near the feet, used a drum sander in a cordless drill...high rail was lower,,,with a beltsander, and couple spokeshaves..and a palm sander..until finally..
519744
The Stanley No. 80...

Up date time...the 2 sides were clamped together, inside to inside...the back stiles already have their rebates milled to house the 1/4" plywood back. Lined the back stiles up
519741
With the...