yes on the wait leave it a few days on edge with air space between. some percent will have moved. Didnt suggest it as its a cutting board so small sizes and short lengths. Door styles on larger...
Type: Posts; User: Warren Lake; Keyword(s):
yes on the wait leave it a few days on edge with air space between. some percent will have moved. Didnt suggest it as its a cutting board so small sizes and short lengths. Door styles on larger...
This is my other side, it was a field 100 plus year old maples and lovely sunsets. So much for that. I put these in and grew them and keep them lower than the back. They are about 14 feet tall as i...
prices varied on baltic as the supplier told me he had to get it from different sources I past paid 72.00 to 90.00 on baltic 3/4 4 x 8. Their mark up is low and irrelevant. You want to see a mark...
transmissions should be manual. 12,000 cars were stolen in toronto by punk ass kids in 2023. Most of them can use a computer and steal your car in 1 or 2 minutes but cant drive a manual.
...
thought the same
George now that im a billionaire im finding that the matress is getting too lumpy.
Switches are a part of machines.
Gizmos are all those plastic and other things with wheels and. No use for most of them but a mag switch yes for sure. A number of machines came with no starter...
ripped tons of 10 foot solid, if a board started to close and some amount did I just lifted them off.
if power went out and a machine was running it would not start when the power came back on. The switches take care of that when the coil disengages when the power went off. Anyone running a roto...
The day went well though one niece got there before me and for as pristine as I left it some very large bird maybe a condor or some prehistoric beast had used it for target practice and had pretty...
Decided to do some digging on this project today. Im down to about 16 - 18" deep and not enough yet have to check for more roots. Its some sort of maple that a friend took down past.
The cut...
no limit on the trees and why id rather have them than a fence. Parents 45 feet tall you didnt see the homes that bordered their property. They put a road beside my place and ive done that side as...
agree didnt buy his, in the beginning it was only info then this is a sales thing. Doesnt matter its the info and i have a good coffee place. I did give Ethiopian to a friend and he just emailed...
thanks Bill I know all the movies well. I think they have that trimmer at home depot but ill wait till its battery powered.
I think I had that same neighbour, then his wife left and his home...
if you are rich the laws may not apply to you, look at Drakes home on Post Road. Those fences are probably double allowed.
My view fence doesnt cut it. I put in cedars end to end same as my...
Not meaning to give you a bunch of homework and past Gundry has done diet you tubes that make me crazy. These below have lots of good to say about coffee if you are interested. Ironically I just got...
if you want straight material rip it over size then machine it again.
Jacks number is good 1 HP for every 4" of jointer. Look at any larger jointers and that is usually the case or more. The General 8" it came with a 1 1/2 HP and later changed it out to 2". ...
Ive seen some you tubes past hooked up to welders and the ones I saw didnt work.
I barely look at grain, maybe edges maybe not. directions changes in many boards, put the board through and it will tell you. Feed rate is most important I can run birdesye one pass one shot...
I wondered if there is a category in the book for most lies. Turns out there is a category but legal profession and politicians are barred. Guess there would be no room left.
Would makes...
feed rate is huge, being able to control it over and above many planers is the difference between blow out and clean cut. When I have time ill be putting a gear motor on the SCM and maybe the wadkin...
taught hollow ground by cabinetmakers. One aspect right off the bat is there are two points to rest the bevel on when honing, makes it easy and maintains the same angle.
if you judge an Excalibur then consider there were likely five generations. I had two on one saw, they were first generation and primitive but on smaller stuff worked great to square one side then...
went out after 4:00 am Sat (friday night) sky was full of pulsating patterns. No extreme colour and not super bright but tons of it. Video taped and not looked yet and dont think it will show...
got done today. boiled water several kettles woth into a cooler. Different automotive details brushes and only one or two of 10 was strong enough. I took water in a squirt bottle and good I did...