First easy step, did any water come out of the filter drain. Drain the fuel tank and let any water settle out before pouring it back in.
Bill D
Type: Posts; User: Bill Dufour; Keyword(s):
First easy step, did any water come out of the filter drain. Drain the fuel tank and let any water settle out before pouring it back in.
Bill D
I would keep the switch and just add a remote station(s) with the buttons of choice. Most of those big paddle switches are just on off switches and you lose the safety features for both you and the...
Buy a used three phase grinder and use a vfd to run it slower.
Bill D
FPM must include number of knives, two, three or four are common. A four knife cutterhead at any FPM feed will do a nicer cut then a two knife head at the same FPM. Insert or the powermatic quiet...
THis is the way mine works. AFAIK the neutral is only needed for a pilot light type switch not an illuminated one.
Bill D
Title says unusual movement. Eucalyptus splits in vertical spirals as it dries and even while it is alive it can split. Splits easy enough when green. wait a week or more and it becomes very hard...
I was standing in the shop and the lights went out after they had been on for five minutes or more. No noise,smell or smoke. I went to the breakers and found one was tripped off, reset it, got an...
I am having some problems figuring out the shop lights. There is one central junction box in the middle of the garage ceiling. It has one cable for power in and one for the wall switch. I was...
I missed the 2" throttle. I thought it was 4 inch all the way out. That will never work.
Bill D
This photo shows what is probably the factory dust chute. for the 12" planer. Looks like a 6" pipe output.
Bill D.
I think those are jacks from a trailer tongue with a foot plate instead of a wheel on the bottom. Looks like some kind of ratcheting crank handles.
Bill D
Buy stainless pins at your local nail store. They will cost little more than plain iron from the box stores. My nail store is about 1/2 the price of box store stuff. Same for my bolt/screw store....
Spending too much time leaning over the computer keyboard is bad for my back, hips, knees and other stuff.
Bill D
Any makeup air should go through some filters to keep out mice, snakes, bugs and flying insects. Exhaust air ducts should also be screened to keep out bad stuff when the fan is off.The heat...
WW2 vets have a harder time. there as a big fire of ww2 records and the VA pretty much has to take any paperwork a ww2 vet can come up with. My Civil war vet Great grandfather has better records...
AFAIK you have to make your own nut cage etc to make it a self ejecting drawbar. R8 tends to fall out on its own. Most other milling taper sare much more angled and tend to fall out on their own....
Probably too cold in your area but I would think rainbow eucalypus would have varying coloring.
Bill D
If you were paying to use Kluber grease you would be using as little as possible. Probably cheaper to buy a used motor with good bearings then the grease.
A one kilogram can on Amazon is $429. ...
My Jet Mini mill is mt3 with a drawbar. Probably made around 1976.
BillD
Any relation to the safety speed cut panel saw?
BillD
If so then it should be confiscated and sold since it was used in the crime. They do that for drug dealer cars don't they?
Bill D
Some machines use zerks but they expect you to pump oil into them. Using grease will gum up sliding ways and cause wear. A properly greased bearing has about 30% grease 70% air in the open space....
Probably none. Unless you want to remove the endcaps so the old grease can be cleaned away before running the motor. You say it has grease zerks. Does it also have drains/vents to allow the old...
There was a thread about the correct name of this hardware in the last few months.
AFAIK most Simpson hardware can be ordered in stainless. Or just buy SS strap and cut /drill to need.
Bill D
I thought they used to be brass? Not brass plated.
Bill D