My Powermatic came with a bottom stop. works great.
Type: Posts; User: James Hansen; Keyword(s):
My Powermatic came with a bottom stop. works great.
Maybe your DC is not turned on. :D
No color, just three coats of Enduro-Var.
289641 This is the upper portion of a kitchen pantry with fixed shelves. as you can see in the picture it is tight. I can get the gun in-between the shelves but it is very tight. should i just foam...
I went from a Unisaw (which i purchased new about 24 years ago) sold it and got a PCS 3HP with a 52" and a ICS mobile base, love the base with the hydraulic lift and full swivel casters so you can...
Thnaks David, I am thinking that is what I am going to lean towards.
Andrew, on my Apollo 1050VR, I am spraying with 6PSI in the window, you think I should try less?
I am spraying Endoru-Var, but I am sure my question would be applicable to just about any product.
My technique for shooting something like a door is to use a peice of plywood with screws in all...
great info Frank. I am having pretty good results today. I switched from a 1.5 to a 1.3 tip and nozzle, I am using E-V straight, no thinning, using a bit less pressure, my Apollo 1050VR is showing...
Thanks Andrew, I also talked to Tom from GF's and he gave me some good tips. I am going to try a 1.3 tip and no thinning.
I am having a bit of a problem with follow on coats of GF Enduro=Var.
I am using a Appolo 1050VR and a 7500 gun with a 1.5 needle / nozzle and a B cup
If i spray E-V straight it is a bit...
When I make ply shelves, I use 1 1/4" X 3/4 end caps on the front and back with what ever material the rest of the project was made with. This not only makes them very strong, but gives it a nice...
I have a couple very large cabinets that are going to be sprayed with GF Enduro-Var.
they have so much area that I would like to break them down to a few (still good size) manageable sections. ...
I just got done building 21 drawers, they are 1/2" maple. About 5 ended up a bit tight, so I used my 6" jointer on a very shallow cut. worked like a charm!
I just sold mine for $800 and it was in very good condition. probably about 10 years old.
Matt asks a good question, what condition is it in?
I got very interested in this because I am about to spray Enduro-Var on my maple cabinets.
I did a test run with my Apollo 1050VR and the 7500 gun. With the 1.5 MM and straight Enduro-Var, I...
I'll add some other +'s of the Shelix head, I went form 15" with straight blades to a 20" Shelix head (planer) . with a lot of time spent setting up straight blades, you will still get some waviness...
Check out Grainger, they have about every caster on planet earth.
I had the same thing happen with my Unisaw, Does your saw have a magnetic switch that is in a large panel away from the switch on the front? If so, check the micro switch that is activated by the...
nope, unfinished.
3/16" may be a bit over what i have, and the worst door is a very tall one, about 4 feet tall, so the warp is amplified. Pretty sure some of the stiles had a bit of a bow to them and I would assume...
Out of my 25 maple stile and rail flat panel doors, A few have a slight warp. Not real bad, We're talking flat against the face frame, one corner will be about 1/8 to 3/16 away from the face frame. ...
I recently sold my 15" Jet planer and got a 20" PM with a Byrd Shelix head. If you haven't looked into a planer (or jointer for that matter) with a Shelix head, I would highly recomend it. The ease...
I owned a Unisaw for over 20 years, just sold it and got a Sawstop PCS 3 HP. I'll never look back.
Thanks everyone. I think you all have talked me out of urethane. I think I will go with one the General finishes products.
Phil, I am not sure how they came up with a quote that high, I was...
I am getting close to finishing up my kitchen cabinet project (building) We are talking a huge job, 9 cabinets, 2 of which are very large pantries, lots of doors, lots of drawers, drawer faces and so...