Search:

ok, to get the rebates milled..
519750
Had to move these out of the way...cauls were a might too close to my arms as they were going by..
519751
Used the Craftsman3720 to mill a 3/8" wide by 1/4"...

Curved areas near the feet, used a drum sander in a cordless drill...high rail was lower,,,with a beltsander, and couple spokeshaves..and a palm sander..until finally..
519744
The Stanley No. 80...

Up date time...the 2 sides were clamped together, inside to inside...the back stiles already have their rebates milled to house the 1/4" plywood back. Lined the back stiles up
519741
With the...

Had to replace a curvy one..
519686
Had enough "Leftovers" for that..
519687
The wide one on the bottom..isn't quite that wide, any more

The best 9 rails are all clamped up into a single...

These 2 planks..
519682
Needed to be cross cut in 24" (Roughly) lengths
519683
Then run through the rip fence at 1-3/8" width...
519684
Then needed to skinny them down to 3/4" thickness.....

Side #2 is out of the clamps..
519681
And Standing in front of Side #1...back to back...one foot will need trimmed a bit, otherwise, they match up quite nicely

2 hours and 20 minutes in the shop, today...Results?
519667
Well..there is the inside of Side #2...being glued up..
519668
Had to get 8 raised panels and 9 rails all spiffy-fied up..
519669
And...

Shopping trip..$108.86
Need to load this up..
519606
Into this space..

519607
Needed to fold the other back seat down..so the 8' long 1 x 4s will fit...The six 1 x 2x 6' were a tight...

Well..I did try to get $20 off....but..he only allowed the 10% the Mall gives...on anything over $40...

Cheer Up....Yard Sale Season has started around here...

The Boss is coming home next Wednesday Afternoon-ish...Same day as Pay Day...I get to go out, and pay the bills that morning, then go pick her up. Being released to Home Health Care.

She also...

A dry fit that also involved a panel...
519596
Did not go well...seems I will be doing this, tomorrow...again..
519597
The Dreaded Too Fat Rebate....back has said enough for today...and..
519598...

2 stiles also got their feet sawn...
519594
Was a good thing that this was the "inside" for both Stiles..
519595
As both had a few "bad" spots, all on one Face...the other face was clear...

Dry fits..first one of the day..
519591
And the Last Dry fitted rail of the day..
519592
18 Mortises were chopped and fitted to the rails, today...tool?
519593
Nothing real fancy...I just sit...

Well, that glue-up is now out of the clamps, and standing up on it's own 2 feet..
519589

Next 2 Stiles look like this..
519590
2 hours IN the shop, today...then go upstairs and mow the yard......

Set one stile on the bench and into the jig....it was marked for "INside" so set that face away from me...then glue on tenon, and a spot of glue in the center of a panel..and worked my way down to...

Rails needed to look spiffy, of course..all 9 of them..first task was deciding which face looked the best..
519555
And which didn't quite make the grade...flipped this one over..
519556
And ran...

Hmm, try again on photos..This morning worked on getting Raised Panels ready..
from this..
519552
Saw marks, burnt spots, ridges. and rough stuff..to
519553
Ready to sand to 180 grit...a Stanley...

Plan last night, was to haul a stack of supplies to the shop, and bring a hamper of dried clothes back upstairs...

Plan got changed a bit..set all these aside..
519524
Set up the #3Stile in the...

Hauled a stack of supplies to the shop, tonight....decided to fix the two wide rails...then went ahead on chopped the 9 mortises in the matching stile...then brought up the clothes from the Clothes...

The "G" was for Government Contracts (WW2)..The "B" merely meant an Improvement was made..of some sort..either an upgrade, or to make a tool easier to Make.

Like: a No. 9BGC model....which...

Maybe later today?
519510
Move things around, and chop the 9 mortises in Stile #3...to match Stile #4's 9...and prep things for a glue up?

Then, while Side #1 sits in the clamps for a few...

So far, so good..
Before the Raised Panels could be Dry Fitted up..needed to work on the face that will show, a bit.
.519506
Removed any saw/burn marks...and ridges..and get things nice and...

Ok..back to doing "Spoon feed" for the photos..and see IF things are any better...
Had FAT Rebates..
519504
We have ways..
519505
Run the Craftsman No. 3720 ( Sargent No. 79, Type 2) along...

This one was in use, today..
519487
Fine Tuning rebates...so that the rails will go on better...without binding..

Been complaining about that Photo BS for MONTHS now...nothing was ever fixed...I have to go back and RELOAD each and every photo AGAIN...

And..it is only on THIS site, that this happens...yet..a...