I built this one several years ago, and it works well. I used C-3 grade birch plywood from menards and only have about $35 into it:
http://www.australianwoodsmith.com.au/pdf/63MitreSawTable.pdf
Type: Posts; User: Todd Hoppe; Keyword(s):
I built this one several years ago, and it works well. I used C-3 grade birch plywood from menards and only have about $35 into it:
http://www.australianwoodsmith.com.au/pdf/63MitreSawTable.pdf
What a great piece and great story. I hope that you keep a written history of the chest with it, so future generations know the family history involved!
Just saw this old post, but I wanted to mention that this inexpensive gun works really well. I have sprayed a bunch of General Finishes Enduro and Target EM6000 with it (tinted black with universal...
Hi, sorry it took a couple of days to respond on this. Here is the thread that talks about the build: http://www.sawmillcreek.org/showthread.php?123619-Crib-Project
It shows the hardware I made...
This is probably the one area where I would suggest following the regulations to a T, and then do as much as you can to exceed them. Selling the crib or not, there could not be anything worse than a...
Menards in Grand Rapids and Lansing stocks 4x8 sheets of "Baltic Birch" plywood. I have never seen the 5x5 sheets there. Good stuff. Lots of plys. About $68 per sheet. I bet that the Detroit area...
Hi Peter,
Have you considered making this table expandable using slides and drop in leaves? If you did that, you would break up the length of the breadboard-ended sections into manageable pieces...
Amazing. What is such a vehicle used for? Is it intended for a specific purpose, or a variety of uses? Parades?
Thanks! I'm not sure how I missed the post that I won for two weeks. In any case, THANK YOU MARC AND TRIENS AMERICA!!!
+1 on McFeeley's. I just put 9/16 OSB on several walls of my garage, about 25 4x8 sheets. I bought a 5# container of 1.75" spax screws, and it worked well. It was much easier to predrill the holes...
Please enter me. Thanks!
Thanks, guys
Thanks , Tom. Do you have more information on your build? Can you estimate the amount of time you have into the project?
Thanks guys. Has anyone seen a review on the newest 2hp Laguna? It looks interesting, but pricey.
I'm looking for some advice on dust collection. I have a small 1 stall garage shop in my new house, that I'm just setting up. My large tools have been in storage for almost two years, so I'm...
For what it is worth, when I built a new house earlier this year, the garage subpanel cost an extra $350. This included your exact same setup (100A, 12 bay subpanel) but about 75' of aluminum wire,...
Matt:
Johnson's in Charlotte is open Saturday, and you can pick in their block warehouse.
thanks very much!
I have a different take on this. I would spray in the house if you can make it work with ventillation and dust control. If you have crown molding on the cabinets and other trim details, you can...
I just use a piece of plywood with some toggle clamps screwed to it. After I mark and place one leg, I screw on another piece of ply as a fence. It works great. Perhaps some T-Track would make...
The problem seems to be that the face of the taller corner cabinet and the lower upper cabinets are even at the edge. Would it be possible to remount the corner cabinet, and build it out from the...
Wow! That is a nice first project! (You also have a really nice shop, especially for a guy doing his first project!)
Your finish is beautiful as well. Can you explain your finishing schedule?
Drive the car around a bit before you remove the cover, and let the wind blow it off of that...
I say go for it, and nix the labor charges.
To make the template, why not just trace the actual door? (I haven:t built such a door, but that seems like it would be the easiest route to go...)