that is a really cool tool
Type: Posts; User: Erik Christensen; Keyword(s):
that is a really cool tool
folding drying rack out of cherry & stainless steel tubing....
384771384772
any new activity that necessitates new cool tools that are affordable... is a very good thing by definition
always used blums as I like their soft close. as with most slides a square box and properly sized square drawer are essential.
I use them exclusively even in situations where the concealed look...
I guess the next logical step to that is.... some instant super foam core with MDF edge banding :)
I can usually find nice quarter-sawn veneer in cabinet grade 1/2 (drawer bottoms) and 3/4 (cabinet boxes) locally that matches the wood I am using (walnut, oak, maple, or cherry) for the project. I...
all my pipes are 6" pvc S&D pipe all the way to the tool - I bent PVC fittings, made wood/epoxy adapters so it is 6" at the tool itself - that DC just plains works - you will be amazed - only time...
I have a pentz 5hp (early clearvue) with 6" to TS base and 4" to sharkguard - am a fan of more air is better - even cutting MDF there is very little dust that escapes
can't say if 3" would be...
I was not so lucky - ordered a G0766 on 1/6 & was told early march ship date, called 3/23 and was told 'May 29... MAYBE' so I cancelled. Now starting the lathe search all over again... sheesh.
it's a tool - if it still works (acceptable cut quality & vibration) then keep using it till it no longer works then discard
what mike said - small stuff can be hard to hold, have small off cuts, leave fingers close to the blade & a catch can easily rotate part into blade
small stuff does not typically need the power of...
if you still want to run a local app instead of a net connected browser - https://www.sketchup.com/download/all
OK - while we are whining about grizzly backorders - I just called about expected date for next container of GO776 lathes as I ordered one last weekend and was told early march..... that is soooo not...
i think most buyers would notice full extension slides & soft close before drawer box construction. If the drawer boxes are going to be painted I think the dovetails are a lot less noticeable.
Me...
just finished a live-edge slab dining table for outdoors - 4' x 12'. spent a lot of time hand sanding the live edges after rounding over sharp edges with a rasp - worked great but did spend most...
I have just the robland saw with sliding table so can't comment on other tools. As a table saw it is OK - I did not end up using the sliding table as much as I thought and the saw has some issues vs...
I got a super nova for my lathe and it works so well it spends a lot of time on the bandsaw, with the mag switch it takes longer to hook up the DC hoses than to install & position the light..
...
i always throw a few domino's in so I do not have to try to fight this - dowels also work
guys like derek take all the fun out of woodworking.... come up with a way to do is safer, faster, easier & better with just simple hand tools...... where is the tool budget going to end up with...
I like maple with a initial finish layer of BLO to pop the grain & add a yellow tint - that should lighten up the cold colors of the room
yah that is pretty cool - the spacing is important for those festool MFT tops - I have a right angle clamp jig for door glueups that I made that registers on 3 3/4" dowels that drops in the top where...
if you have a track saw with a good rip blade it would take 5 minutes to correct - rip along existing joint - with a good blade you have a glue ready surface on both pieces, clean up edges with...
all the bin has to be is air-tight. if your bin leaks you will get upward flow in the cyclone that will carry over fines to your filter.
shape is not significant - just make sure you have an easy...
check out Tropical Exotic Hardwoods in Carlsbad CA - looked at inventory on web site before visiting their location and found the website to be accurate as to what they have in current stock - have...
grizzly offers a number of butcher block bench tops that you can cut down - when I looked at them for a few tops at work it was not much more than hard maple would have cost much less time to...