Jim, I did research a bit on this here on the forum. I did see a comment of yours that you straighline rip on a slider. I have a conventional table saw ,so do infact, like the wide jointer due to...
Type: Posts; User: joel cervera; Keyword(s):
Jim, I did research a bit on this here on the forum. I did see a comment of yours that you straighline rip on a slider. I have a conventional table saw ,so do infact, like the wide jointer due to...
I've got a FS350 jointer/planer combo( with straight knives) I've had for a few years. I love the machine. But sometimes hate the change over. Usually I can bulk process jointing vs planing but its...
Yep I plan on finishing before installation. Nice suggestion on their slate for finish/ drying. Thanks.
I find the oil's effect on DF's color to be aesthetically pleasing. Compared to unfinished.
Thanks for the comments everyone.
I'll try to knock down the surface with a sander before applying the oil. That makes sense.
I've built a new 950 sq ft 3 car garage/workshop. I have just received a load of tongue and groove rough sawn doug fir that I will becovering the rear wall and ceiling with. 3/4x8" . My buddies...
I'm in Sonoma County CA. Bout an hour north of San Fran.. Thanks and PM me if you'd like to discuss.
Thanks for all the suggestions everyone. I'll hit up a local metal supplier round town to see what prices are. The Bies kit from amazon for 52" is around $250.. So that's what I'm working with as...
I've got a Biesemeyer fence on my vintage Unisaw. Ive been running it on the original 34 or 36 or so inch rails my fence came with. I've been working out of a 2 car garage shared with the car so the...
You guys are awesome. Excellent input. Various solutions proposed and I’ve got a bit of figuring to do. Thanks all and I’ll post when the doors are hung..
463861463862Hmm. I have been puzzling over what I thought was done to the cabinet in this in this image. The rabbet you mention does now seem likely. although at other points it simply looked like a...
Building some Cherry nightstands for my wife and I based on a Stickley Ellis design we both like. I am having the doors and drawers recess below the front face of the nightstands by about 1/8 inch. I...
Ya the more I think about it .. i'm leaning towards stripping the top completely and refinishing it to match. maybe cutting off the edges and adding some wood to keep the original width. Though...
439887439888439881439883439882439884Here are a few more photos showing some of the less important dings and damage the I'd like to minimize. Tho as stated even just wiping on some MS helps some of...
I picked this up on Facebook marketplace today. Paid $250 for it hoping I can repair a few imperfections it has and put it into service in my living room. I have experience with aniline dyes and...
Hand plane shavings get caught in the dustopsper separator sometimes. Ideally the dust stopper works best on dust and chips. Long curly shavings get caught up more readily and require manual...
Yes. I strop. 1000 then 4000 water stone to hone then strop on leather over mdf charged with green compound. By all measures it makes my edges sharper. and its cheap to boot. I could go buy an 8k...
Love the table Derek! And ditto for the Ishitani furniture channel on YouTube. Great woodworking videos! No talking. Just woodworking. And he has wonderful designs. It’s fun to watch a skilled...
The above seems to jive up the same as the YouTube vids I saw comparing DD vs DS. DD has a very tiny edge in performance. But in actual use I think it’s a moot point. As I said in another post,...
Nice! I just posted about this again in the new Duststopper thread. I really liking my setup so far. Hope you enjoy yours too.
although it does beg the question " When will they start making vacs...
My old Ridgid Shop Vac finally gave up the ghost about 2 weeks ago. After I decided to get another one (instead of a fein/festool type vac) I then decided to add a dust deputy or similar to help...
That is an awesome bench. And unlike many of the benches we normally see these days. Enjoy! And thank you for sharing.
I've used shim stock cut from aluminum cans many times on my Old wood working machines. . Its worked great even doubled or tripled up. Unless you need more thickness.. Than something else might be...
I did restore the Delta 28-350 bandsaw as well. Its also dated to the 50's. its a great machine. It had a 3/4hp Repulsion induction motor that was not original to it. Underpowered as it was I found a...
Just wanted to post some pics of this. I searched the internet for someone who'd done this but found nothing. Just in case someone in the future wants to see how someone else did it.. Here's how I...