Used planer recommendations

[steven taggart]

Avoid the steel city, and the craftsman, performax, and other brands that are the same unit. The gearbox fails. Dramatically.

[Tom Porter]

Thanks for the help. I'm not in a huge hurry so I can bide my time until I find a good deal. At least, that's the theory.

[Jeff Bartley]

Tom,
I'd chime in to say that yes, the 735 does leave an outstanding finish with new knives (as well as any I'd say), but you can't take off much in one pass. On wide harder hard woods expect to be taking a quarter turn of the knob (64th/in). It's painfully slow. And loud! But all that being said you can pick up a used one relatively cheap and be up and running in no time. I actually like the older Dewalt 733 for a lunchbox planer, only has two knives but they can be sharpened. I have both a 733 and a 735 in the shop and as soon as I upgrade I'll sell the 735 and keep the 733 for taking to job sites. I plan to sell the 735 at a price to move quickly!

[Jim Mackell]

Tom, .......... But all that being said you can pick up a used one relatively cheap and be up and running in no time. I actually like the older Dewalt 733 for a lunchbox planer, only has two knives but they can be sharpened. I have both a 733 and a 735 in the shop and as soon as I upgrade I'll sell the 735 and keep the 733 for taking to job sites. I plan to sell the 735 at a price to move quickly!

Market must be very different in your area. I've never seen a used 735 offered in my area. Used 733's generally go for $250. - $350. I'd hold out for a 735 either new or used.

[Tom Porter]

Dewalts pop up around here, though they tend to be closer to $300 than $200, as one might expect. A 735 would be my first choice but might have to go for a less expensive choice for a while. I have a project in mind with some reclaimed lumber that might not wait until I can justify a bigger investment. Besides, the amount of time and skill I have to apply to woodworking do not encourage spending a lot on equipment (I'm only about 2 hours away from Jeff, though, so I might see his 735 on Craigslist sometime).

[Jeff Bartley]

Tom, when I sell my 735 it'll go up here first!

[John TenEyck]

I agree with the poster who said think old, American (or Canadian), cast iron. I bought a Foley Belsaw planer/molder a few years ago for $275; my friend just bought another one for $250. 5 HP motors, easy to work on not that I need to do much, run forever. If you have the room, I would get a stationary machine. When you're done with it you can sell it for what you paid for it - not so with a screaming lunchbox one.

John

[Howie Rosenberg]

I have a Rigid R4330 that I picked up on CL used for $150. It is a 13" thickness planer and works very well. The blades are double sided and you can get replacements for $30 at HD.

The Dewalts are generally thought of as the highest quality lunchbox planers but since I am only a hobbyist I did not want to spend that much which is why I went with the Rigid. I have also heard good things about the Steel City planers but have never used one.

Patience on CL is key. Keep looking and the right deal will show up.

[Danny Hamsley]

I had a DW733 that planed thousands of BF. The knives can be re-sharpened, but you have to have equipment to do that, or send the knives off to be re-sharpened. The DW734, as has been mentioned, has three knives that are disposable. They have two sides, so when one side gets dull, you turn them. Then buy a replacement set when the old ones are dull on both sides. The cutterhead lock on the DW734 is excellent. These DeWalt lunchbox planers are real little work horses that for the money, are a very good performer. A proven performer. I have moved up to a 15" 3 HP and a 20" 5 HP (with a 2 HP feed motor), both with spiral heads, but I fondly remember my "little screamer" days with the DW733.