Hello,
I'm a member of a few WW forums and after doing a lot of reading here at SMC over the last few months feel it's time to post something. Some of the members might appreciate these pic's of the Technomax CU410 Elite 6-1 Combo with the 8.5' slider. Mine is on order and should arrive here in Canada late Nov - early Dec, I've also ordered the equivilent of the MM16 Bandsaw which will arrive at the same time. As far as options go I have ordered pretty much everything including the feeder support. The sales service from Coopers & Horton (Toronto) has been excellent, I believe that I will be one of the first Canadian recipients if not the first for a Technomax CU410 Elite combo unit and can't wait to get it into my workshop.. but yes its quite the wait isn't it!
Regards,
Wayne
CU410 Elite Technomax.jpg
Feeder support option:
FeederSupport.JPG
Technical features :
- max. working width of surface tables 410 mm
- total length of surface tables 2000 mm
- tiltable surface fence 90-45 deg.
- thicknessing table dimensions 775x423 mm
- 2 feed speed on thicknesser 6-12 m/min
- min/max working height on thicknesser 3/230 mm
- saw-spindle moulder table dimensions 1250x430 mm
- sawblade tilting 90-45 deg.
- max. diameter of saw blade with
installed scoring unit 315 mm
- max. sawblade projection at 90 degrees from table with blade diam. 315 mm 100 mm
- max. sawblade projection at 45 degrees from table with blade diam. 315 mm 70 mm
- max. squaring stroke (CE/non CE) 1800 mm
- cutting width on rip fence 1050 mm
- max. spindle working height 125 (70 if 3/4") mm
- spindle moulder speeds (50 hz) 3500-6000 8000-10000 rpm
- max. diameter of tool lowered under table at 90° 210 mm
- max. diameter of tool lowered under table at 45° 150 mm
- max. tool diameter when tenoning 275 mm
- motor power (n. 3 motors) 4 hp 3 kW 50 hz (4,8 hp 3,6 kW 60 Hz)
- 3 exhaust hoods diameter 120 mm
- 1 exhaust hood diameter 60 mm
- net weight basic machine (fixed) 875 kg
- spindle moulder available with following diam.: 30 - 35 - 40 - 50 mm, 3/4" - 1" - 1 1/4"
Standard equipment:
- anodized aluminum wagon sliding on high precision hardened steel guideways (dimensions 290x142x1700 mm)
- cast-iron saw carriage with lifting by means of "dove-tail" guide and tilting by means of side trunnions
- crosscutting support with dimensions 1100x650 mm, complete with: . telescopic fence L=1840mm (3200), with 2 crosscut flip-over stops and
eccentric clamp
. telescopic swinging arm support
- dedicated saw rip fence L=1200mm with micrometric adjustment and cam-locking complete with support
- sawblade protection on riving knife (exhaust hood 60 mm diameter)
- cast-iron spindle moulder unit, 80 mm diameter
- spindle moulder fence with micrometric adjustment
- spindle moulder shaft lifting on machine front
- saw-spindle moulder table extension
- surface planer tables opening on saw/spindle moulder side (inwards tilting)
- cutterblock 87 mm diameter, with no. 3 knives HSS 410x30x3 mm and cast- iron supports
- dedicated planing fence complete with support (1520x150 mm)
- planer protection
- presetting for mortiser
- ribbed cast-iron worktables
- operating groups adjustment by means of fixed handwheels
Options Included:
58.02.58 Version with maximum squaring stroke 2700mm
58.02.59 Belt driven scoring unit complete with saw blade diam. 100mm.
58.02.16 “DADO SET” capability (tool with max diameter 8”)
58.02.66 Idle roller on squaring frame
58.02.13 Angular cutting device equipped with:
- Telescopic fence with two flip over stops
- Pre-set for angle selection
58.02.89 Cast iron mortiser with exhaust hood diam. 120mm
- Table dimensions 450x220 mm
- Strokes x= 160mm y= 120mm z= 105mm
- Extractable operating levers
58.02.19 Self-centering Wescott type chuck 0-16mm
58.01.79 “TERSA” cutter-block with 4 knives
58.02.25 Tenoning table and protection hood (max. tool diam. 275mm)
58.02.69 Tiltable spindle moulder 90 / 45 degrees
58.02.26 Reverse spindle rotation
13.02.50 Interchangeable spindle
13.14.0 Spare spindle for router bits ˝”
58.02.50 Wheels for machine movement
58.02.51 Numerical readouts for the units positioning (saw and mortiser lifting excluding)
58.00.21 3 single phase motors 4.8hp 3.6Kw 60hz
08.87.32 Triple wall for version with 2700mm stroke (packaging)
58.02.60 Round sliding bar on saw fence for parallel cutting and on surface fence.
- micrometric adjustment and cam locking system “high rigidity” cast iron fence supports
- Support device for feeder
Reply With Quote