The wobbling, the limited power, etc. Never mind all of that. It's too short to turn a tool handle!
The wobbling, the limited power, etc. Never mind all of that. It's too short to turn a tool handle!
HA ... nobody told me that!
Mine's not too bad, but I havent asked it to do anything crazy yet! And what kind of tool handle ..... a shovel !!!!
Actually, just a turning tool handle. You can turn a short one but that's about it without an extension. Don't get me wrong...the mini is actually pretty nice. I pretty routinely turn 7" and 8" bowls on mine, but it's very hairy until I get it somewhat balanced, and it vibrates quite a bit through the cuts, especially the hollowing cuts. Anyhow, I was going to pick up a couple of Thompson tools and I figured I'd just turn some handles for them, but all I can turn are short handles. I guess it's time to do research on who makes a good handle.
You can get bed extensions for most of them. I have even seen risers for the headstock and tailstock.
robo hippy
John,
Since you are thinking of getting a couple of Thompson tools. Take a look at the Thompson Handles he has two types now the one he shows on his Web Site and one that has a foam cover(new style not posted yet) they are both great an his prices are lower than most Aluminum Handles on the market.
I found I could turn a 14 inch tool handle on my Jet, but it took a bit of courage to perch the tailstock halfway over the very tippy end of the bed ways...
As for bouncy bowl blanks.... That's what they make bandsaws for! Unless of course your blank is taller than your saw's capacity... Then you not only need a bigger lathe, you need a bigger bandsaw! Where does it stop?
CarveWright Model C
Stratos Lathe
Jet 1014
Half-a-Brain
John, while you are researching tool handles and such, you might want to check into who makes bigger lathes. And then check out how to post on Craigslist..... And then have a talk with your woman.
Jim, it doesn't!
Well, my bandsaw's capacity won't be limiting me for quite some time I don't think.
re: everything else
Naw, I'm keeping the Mini. I like it. I think a DVR is in my near future, though. Maybe even a Powermatic, but I'm leaning towards the DVR at the moment.
John...
To bad you're not closer, I would invite you over... we could visit, swap stories, talk a little turning trash, and you could use a bigger lathe to turn your handles.
I recently upgraded from a delta midi to a 3520B. My first lathe was a Delta Iron Bed... forget the model nbr. I sold it for the midi and recently upgraded to a used 3520. Now the midi seems to be on permanent load to the girl friend of the LOML... I miss it to...
How many of us think of our tools as our kids... ya just can't seem to want to get rid of them.. but ya gotta clean house to make room for the newborns?
Thanks for listening
Joe
John,
I think we are kinda close. If you want to try a Jet 1642 (a mustard monsters sister), give me a shout.
For less than half the price of the PM, I think it's a worthy tool.
Just saying
Greg A
Some people seem brighter after being set on fire
John, just get Doug's handles. I really love mine they are super nice. Right now I have one 5/8" mouth 1/2" mouth and a 3/8" mouth, I just swap the tools in and out as needed, only takes a second. They are heavy duty filled with steel shot and really built to last. The threads and grub screws are hardened steel so they won't wear out or cross thread with repeated use. They are really super comfortable and well balanced with his tools. I will be ordering some more soon with my tool money from Christmas.
“I am enough of an artist to draw freely upon my imagination. Imagination is more important than knowledge. Knowledge is limited. Imagination encircles the world.” ~ Albert Einstein
Randy (Monster Hollowing) makes great handles too!! All of my Thompson's have Monster handles
Your Respiratory Therapist wears combat boots
+1 for Monster handles.
Bernie
Never put off until tomorrow what you can do the day after tomorrow.
To succeed in life, you need three things: a wishbone, a backbone and a funnybone.