My dentist gave me a new air drill, he did not like, it will turn 400,000 RPM. I have ideas for inlays, and pendants.I also got a lot of bits with the tool. I would like to try some lace features on small bowls, Any advice would be welcome.
[OP]
Guest
My dentist gave me a new air drill, he did not like, it will turn 400,000 RPM. I have ideas for inlays, and pendants.I also got a lot of bits with the tool. I would like to try some lace features on small bowls, Any advice would be welcome.
Contributor
Dennis, I know nothing about piercing, but I did talk to my dentist about an air drill. They are expensive! You really scored with this one. I do understand that the bearings in these things are super sensitive to moisture, so a very good filter system is a good idea.
I look forward to new projects from you! Scott and Richard Kennedy need some competition to keep them on their toes!!
Member
You are in for some fun. I just came inside from a piercing session. The key piece of advice is "air flow" even outside there was enough smoke produced to make my eyes water until I set up a shop fan to blow on me.
The key piercing bit is the 699L (~$2.50 apiece)
Practice on egg shells before you pierce a bowl so you get used to using the tool on something you don't have any time investment in.
If you are not used to turning thin walls (1/8" and under) it's time to master the technique. I built up a stash of thin bowls while I learned to turn thin and practiced piercing on eggs.
Member
If piercings don't work, you could always resort to doing your own fillings!
Last edited by Greg Just; 07-28-2011 at 9:09 PM. Reason: typo
Member
Looks like a great score! Beats the heck out of my dremel!
Contributor
Now that is a gloat.
Bernie
Never put off until tomorrow what you can do the day after tomorrow.
To succeed in life, you need three things: a wishbone, a backbone and a funnybone.
Member
Congrats! I need to talk to my dentist!
Contributor
Eric, where are you buying your bits? The only carbide bits I found were at craftsupplies. I like the medium tapered bit the best for piercing but none of their stock numbers match your number.Originally Posted by Eric Holmquist
Dennis, a fan IS a must (for piercing AND burning) I bought a little $5 desk fan at WalMart and it works great for this purpose. AND you must have a water filter and regulator for the drill. 35psi MAX to the drill.
-------
No, it's not thin enough yet.
-------
Member
Nice gloat. As someone who had a lot of cavities as a kid, I wonder how long it takes until you don't wince when you hear the whine of the dentist's drill.
[OP]
Guest
I also had cavities as a kid, only problem in the 50's was there was no whine, they were belt driven, and it took a lot longer.
[OP]
Guest
The good thing about what you said is that now days, I can take my teeth out and work on themIf piercings don't work, you could always resort to doing your own fillings!
Member
These 1/16" shank bits are dental burs and there is an international standard for their numbering. CSUSA hides this standard number from you. Other suppliers like
Turbocarver http://www.turbocarver.com/burtypes/body_burtypes.html
Burs for Carving http://www.bursforcarving.com/FGBurs.html
Treeline USA http://www.treelineusa.com/power-car...16-carbide?p=3
Bihn Pho http://www.wondersofwood.net/
Sell them by their ISO number. Treeline only has the 699 in their online catalog but stocks and sells the 699L on request.
I'm sure there are others that sell the 699L, these are just a few that came quickly to mind
Contributor
Whats the difference between the 699 and the 699L?
-------
No, it's not thin enough yet.
-------
Member
Just purchased some bits from Craft Supply. Copied off of their website:
#699 Small Cross Cut Tapered Fissure Cutter
They are $2.25 each
Member
The 699L has a slightly longer cutter head length, 5.2mm vs 4.2mm for the 699
Posting Permissions
Reply With Quote