I only use metal slides in "cabinetry work", never on "furniture"...at least to-date.
I only use metal slides in "cabinetry work", never on "furniture"...at least to-date.
--
The most expensive tool is the one you buy "cheaply" and often...
On most items I have made, I used metal slides. I find that good slides make drawers work well and also make customers happy. Wood slides will wear in time and get loose or sticky. Metal slides don't change with age for a very long time. If a drawer is going to se much use (1-2 times per day) then it gets metal slides. If it sees only occasional use (1-2 times per week) then wood runners are probably okay. Think of how many times it will be used in say 10 years. (1-2 per day = 3600-7200 times in 10 years; 1-2 per week is only 500-1100 in the same period of time)
With regard to "traditional" furniture making. The way I look at it if the Shakers had been able to get metal slides, they would have used them. You don't see metal slides in furniture from 50 years ago because metal slides didn't exist where the common woodworker could get them or afford them. I see more and more Amish built furniture with metal slides. You don't see many antique pieces with wooden hinges, beacause metal hinges became easy to get at a reasonable price way before metal drawer slides hit the markets.
Just my take on the situation, to each his own!
Lee Schierer
USNA '71
Go Navy!
My advice, comments and suggestions are free, but it costs money to run the site. If you found something of value here please give a little something back by becoming a contributor! Please Contribute
Originally Posted by Lee Schierer
I agree....but will say this in favor of traditional runner/kicker/webframe construction with no slides. I can get that 'piston fit' quality in a drawer. The feeling where the last couple inches of closure requires a bit extra push and you get tha slight 'pffffft' sound and also a similar experience when opening.
That is an aspect I've not experienced when using metal slide drawers.
Tim
on the neverending quest for wood.....
I think wood runners endure. I have a few antique dressers with big heavy drawers that are opened daily. They are 80-100 years old and open and close smoothly. I could probobly stand in one and it would hold up.
Are you working for that 'piston fit' in the uncontrolled environement of a shop?Originally Posted by Tim Sproul
Kirk,
Here in the SF bay area.....I run A/C or heat for only 2 months out of 12.
At any rate....there is little/no expansion/contraction in the webframe or in the drawers.
Tim
on the neverending quest for wood.....
Skip,Originally Posted by skip gleichman
Can you elaborate on your system? I am making my first piece with drawers and am not sure if I should go with metal or wood slides.
Jim
The man who makes no mistakes does not usually make anything. ~Edward Phelps
Like most here to see the kitchen style hinges on fine furniture is a abomination.
However this type of runner would be ok with me,apart from the price.
http://eagleamerica.com/product.asp?...cd2=1129411697
.. If walking is good for your health, the postman would be immortal.
Jim,
Can you tell me more about what it is you are making? The easiest place to start is a table with a single drawer but using wooden runners and slides applies to any casework as well. we can likely help if you tell us more about your project.
Skip -- I'm in the process of designing a chest of drawers and i was planning on using runners under the drawer sides, and the sides of the cabinet (solid) as the guides, and leave it at that (ie, no slides). sounds like you use both runners and wooden slides in the same piece. when doing this, do the runners support the weight of the drawers with the slides serving simply as guides, or do the slides also support the weight of the drawers? and do you use slides and runners bc this results in smoother operation than either would alone? do these questions make sense? i am a novice, so it's quite possible that they don't.... thanks, tony
Sorry Tim. You don't live in the Bay Area any more. You bailed and went and moved over the the hill to live in a place where it is a 2 hour drive to work.Originally Posted by Tim Sproul
Michael in San Jose
Non confundar in aeternam
I will try to answer some questions and hope I can explain what i do with any clarity at all.. For an end table (leg and apron design), I will just use runners on each side (machined to also guide the drawer), but have used one in the center for a guide on heavier drawers as well. The side runners support most of the weight and the center is usually used as a guide to make the drawer slide straight. All three can support the weight but that compounds the work required to make everything fit just right. (the Stikley dresser uses three locations of support)
The center runners are easy, just make sure the bottom panel of your drawer is located high enough to accept the two pieces of wood that you will glue to the bottom panel. Or better yet, use one block of wood and put a dado in it to accept the runner. (see pic)
I also have used a simple system that I saw David Marks use on woodworks where he had support at the top and bottom of each drawer end which also works very well though you can't make the fit too tight or contraction will cause binding.
When I first started using runners, the hard part was getting things to line up correctly. And often not realizing I had the right fit because of the drawer feeling "sticky". I usually use maple on maple and even when it is sanded smooth it will sometimes not feel right until there is some linseed oil applied.
If you can access each drawer from the above, you can make the runners and thier support first, place them inside, slide the drawer into them, shim the drawer then measure and mark the location of the runners from the top (think of an "L" shape ... see pic). With some drawers in casework, I pre-build the runners (think of a "T" shape on it's side) and then machine them to rest on the rails in the front and back until a perfect fit is established. This works in projects that have a leg and side panel or apron design and offers added room to fit runners in place.
If there is only a solid case panel on the side of a drawer, the rail has to be mounted directly on the side panel (or fit in a dado.. see photo). You then mark the location of a runner on the drawer from within while fitting the drawer in place.
I wish I could draw or explain this better. I can say that I initially learned a lot by going to look at the highest quality furniture (Stickley, Baker, Thomas Moser) and inspecting the joinery and the interior components.
Skip,Originally Posted by skip gleichman
I am starting a changing table/dresser for my son. I am 3 months behind schedule, but I did manage to build the crib before he was born. Here is a photo of what I want my piece to resemble.
The man who makes no mistakes does not usually make anything. ~Edward Phelps